Delta Servo Motors
Delta Servo Motors
Start Delta servo motor selection with the full motor and drive nameplate codes. Two motors with the same power rating may have different encoders, rotor inertia, mounting dimensions and brake options. Use this page to find the servo motor family installed on your machine, its Delta servo drive and the relevant matching tables. For replacements, check how the motor and drive work together and verify the feedback interface.
Motor families
Delta ASMT · Start here for replacement motors on legacy ASDA-A systems. Check the full ASMT code, mounting flange and brake option against the original matching table.
Delta ECMA · Rotary servo motors with a range of power, frame and encoder options. Look up the exact ECMA model in the applicable ASDA-A2 or ASDA-B2 drive table.
Delta ECMA Legacy 2500 PPR · Earlier motors with a 2500 PPR incremental encoder. Compare the drive combination and CN2 cable in the ASDA-AB or ASDA-B manual for your installation.
Delta ECMA Motors with Magnetic Encoders · ECMA-CM and ECMA-GM motors with 13-bit magnetic encoders documented in the ASDA-B2 manual. Open the category to find the exact motor code, matching drive and encoder cable.
Delta ECM-A3H · High-inertia motors in the ASDA-A3 system. Use the rotor inertia of the exact model when calculating the load inertia ratio and cycle torque.
Delta ECM-A3L · Low-inertia motors in the ASDA-A3 system. For axes that accelerate frequently, check the load-to-motor inertia ratio, peak torque and torque-speed curve.
Delta ECMC · Rotary motors carrying an ECMC nameplate. Match the exact motor code to the voltage class, power rating and cable set in the relevant drive table.
Delta ECML Linear Motors · Coil and magnet-track assemblies that produce linear thrust. Check continuous and peak force, travel, the linear scale and the supported ASDA-A2R drive.
Delta ECMR · Rotary servo motors documented for Delta robot and ASDA-MS configurations. For a spare, verify the robot model, axis number and complete motor suffix.
Delta ECMS Spindle Motors · Permanent-magnet motors for CNC spindles. Review continuous torque at the operating speed, shaft and cooling options, then check the ASDA-S drive combination.
Check the motor and drive combination
Mechanical load. Define the movement profile for an axis using position control. Compare the required speed and torque with the motor curve. For repeated acceleration and stops, assess dynamic response and positioning accuracy under load.
Encoder and cable. Check the encoder resolution, the signal type expected by the drive and the connector pinout. On an absolute encoder system, check the battery box and retained multi-turn position where applicable. Select Delta servo cables using the complete codes at both ends.
Cabinet and control. For a PLC-controlled axis, use the cabinet drawing to trace CN1 I/O, sink/source compatibility and limit switches. Check which EtherCAT, CANopen or Modbus RS-485 functions the drive and its communication unit support.
Editor’s Note
Put the two nameplates side by side when buying used. Ask for legible photos of both the motor and drive codes. A single character can identify a different encoder or brake option on a motor with the same housing.
Check the full mounting dimensions. Compare the pilot diameter, shaft diameter and length, keyway and connector orientation. A few millimetres can keep the existing coupling or machine cover from fitting.
Check the brake separately on vertical axes. Verify the holding-brake option, supply and drive wiring. Secure the load according to the machine's service procedure before removing the motor.
Save the alarm code and settings. For a feedback alarm, check the cable, connector and encoder type before changing the motor. If the fault appears as the axis moves, examine the cable shield and possible electrical noise. Back up the drive parameters before replacement.
Ask for the test results. Check what the seller observed with a compatible drive, including the brake, bearing noise and shaft play. Record the motor and cable codes in the work order for the next servo maintenance visit.
Motor selection tables and PDF manuals
ASMT and ECMA · ASDA-A/A+ manual · ASDA-A2 / ECMA catalogue · ASDA-B2 / magnetic encoder ECMA table · Legacy ASDA-A2 archive manual. English PDFs.
ECM-A3, ECML, ECMR and ECMS · ASDA-A3 motor matching tables · ASDA-A2R / ECML manual · ASDA-MS / ECMR catalogue · Delta CNC / ECMS catalogue. English PDFs.
Related topics
Industrial servo applications · Multi-axis synchronization · Delta Motion Control Cards · Delta Encoder Connectors · Absolute Encoder Peripheral Units
Delta Servo Manuals · Servo Modules and Accessories · Second-Hand Delta Equipment
External references · Delta motion control catalogues · ECML source catalogue · ECMR source catalogue · ECMS source catalogue