Delta ECMA
Delta ECMA Servo Motors
Delta ECMA is a family of permanent-magnet synchronous rotary AC servo motors. The 220 V and 400 V classes cover different rated speeds, flange sizes, rotor inertias, encoders and brake options. For axis control on packaging, feeding and positioning machines, match the motor, servo drive and cable set by their complete order codes.
How to read an ECMA motor code
In ECMA-C10604RS, C identifies the 220 V, 3,000 rpm class, 1 identifies the 20-bit incremental encoder, 06 denotes a 60 mm flange and the following 04 denotes 400 W rated power. R identifies a keyed shaft with a tapped end, an oil seal and no brake. The final S denotes the standard shaft diameter. Delta lists 1.27 N·m rated torque and 3.82 N·m maximum torque for the C□0604□S group. When sizing torque, assess continuous operation and short acceleration periods separately.
C/E/F/G identify 220 V motor classes, and J/K/L/M identify 400 V classes. For example, Delta’s A2 table lists the 220 V ECMA-C□0604□S group with the ASD-A2-0421-□, and the 400 V ECMA-J□0604□S group with the ASD-A2-0743-□. Both motors are in the 400 W class. For motor and drive selection, check voltage, rated current and Delta’s matching table together. Include rotor inertia, gearbox ratio and the machine’s acceleration cycle in the load and transmission calculation.
Encoder generations and related categories
The character after the voltage and speed letter identifies the encoder type. For example, ECMA-C10604RS uses 20-bit incremental feedback, and ECMA-C20604RS uses 17-bit incremental feedback. In the A2 catalog, A denotes an absolute encoder with 17-bit single-turn and 16-bit multi-turn resolution. On specific models, 3 denotes the legacy 2,500 PPR option and M denotes a 13-bit magnetic encoder. In ECMA-CM0604PS, for example, C identifies voltage and speed, and M identifies the encoder. Verify feedback compatibility using the full motor code, drive model and encoder cable.
ECMA legacy 2,500 PPR motors · ECMA motors with magnetic encoders
ECMA catalogs and manuals
ASDA-A2 catalog · ECMA motor selection tables (EN) · 220 V and 400 V motor combinations, model codes and dimensions.
ASDA-A2 user manual · ECMA motor data (EN) · Drive combinations in section 1.3 and motor specifications in section 11.2.
ASDA-B2 user manual · ECMA motor matching (EN) · Encoder codes, connections and B2 compatibility tables.
Earlier A2 manual on OtomasyonAVM · Earlier B2 manual on OtomasyonAVM · Delta servo PDF archive
Editor’s Note
Check the nameplate and shaft end together when buying used. Ask for photos of the label, power and encoder connectors, keyway, shaft end and flange. During bench inspection, review a test record from a compatible drive and cable set alongside checks for shaft play and bearing noise. Confirm the brake option separately.
Record the position if a fault repeats at the same point in the cable carrier. On the B2, AL011 indicates an encoder error and AL026 indicates unreliable encoder data. Follow the manufacturer’s service procedure to inspect the connector latch, cable bend and shield termination. Checking whether the fault coincides with higher motor current or a particular cable position helps distinguish signal noise from intermittent contact.
Record machine zero before removing a motor with an absolute encoder. Save the drive parameters, machine zero, position offset and any battery warning. After replacement, verify position against a known point and follow the machine’s homing procedure. Compare the displayed position with the actual mechanical position.
Check the holding brake and stopping system separately. The motor’s electromagnetic brake holds the axis in position once it has stopped. On a vertical axis, secure the load mechanically before service. If rapid deceleration produces an overvoltage alarm, review stopping time, load and the drive’s regenerative braking arrangement.
Verify motion and travel after replacing the motor. If the same command moves the axis a different distance, compare the electronic gearing ratio with the original backup. If vibration appears at a particular speed or load, check coupling alignment and load inertia. After checking mechanics and feedback, compare auto-tuning and servo gain results under the same duty cycle.
Related topics and Delta units
Motion and position control · Speed loop gain · Servo control loops · Supervisory control in servo systems
ASDA-A2 servo drives · ASDA-B2 servo drives · ASDA-A2-E EtherCAT servo drives · ECML linear motors
Delta servo motor category · Used Delta automation equipment