Delta ECMA Legacy 2500 PPR

Delta ECMA Legacy 2500 PPR Servo Motors

Delta ECMA Legacy 2500 PPR models are AC servo motors with incremental encoders. Delta’s ASDA-B and ASDA-AB manuals list the servo drive codes that match these motors. On machine applications such as feeding, cutting and transfer, the full replacement motor code matters as much as the axis scaling and home settings.

ECMA-C3, E3 and G3 motor codes

C3 · 220 V, 3,000 rpm: ECMA-C30401□S (100 W), ECMA-C30602□S (200 W), ECMA-C30604□S and ECMA-C30804□7 (400 W), ECMA-C30807□S (750 W), ECMA-C31010□S (1 kW), ECMA-C31020□S (2 kW).

E3 · 220 V, 2,000 rpm: ECMA-E31305□S (500 W), ECMA-E31310□S (1 kW), ECMA-E31315□S (1.5 kW), ECMA-E31320□S and ECMA-E31820□S (2 kW), ECMA-E31830□S (3 kW).

G3 · 220 V, 1,000 rpm: ECMA-G31303□S (300 W), ECMA-G31306□S (600 W), ECMA-G31309□S (900 W).

In ECMA-C30604ES, C denotes the voltage and speed class, 3 the 2500 PPR incremental encoder, 06 the 60 mm frame and 04 the 400 W rating. In this example, E denotes a keyed shaft without a brake or oil seal, and the final S denotes the standard shaft size. When selecting a motor, check the frame, shaft diameter, brake, speed and torque together.

2500 PPR, four-edge counting and PLC output

The motor encoder provides 2,500 pulses per revolution. ASDA-B and ASDA-AB count all four edges of the A/B channels to obtain 10,000 internal counts per revolution. Motor feedback enters through CN2. On ASDA-AB, P1-46 can set the encoder pulse output sent to the PLC or axis card. If the receiving counter also uses four-edge counting, include its counting mode when checking the scale.

For position control, check motor feedback, output pulses and command scaling individually. Confirm how the machine establishes zero on the incremental system. When moving to an absolute encoder ECMA model, check the drive’s feedback support and the machine’s homing arrangement.

ASDA-B and ASDA-AB matching examples

ECMA-C30604□S, 400 W · The ASDA-B manual lists ASD-B0421-A. The ASDA-AB manual lists ASD-A0411-AB and ASD-A0421-AB.

ECMA-C30807□S, 750 W · The ASDA-B table lists ASD-B0721-A and the ASDA-AB table lists ASD-A0721-AB. When matching a motor and drive, check both the full model code and the drive’s mains supply. For ASDA-A2 or another drive family, consult that drive’s matching table. Use the device drawings and Delta servo cable tables for power, brake and feedback connections.

Editor’s Note

Ask for photos of both nameplates, the shaft and the connectors when buying used. The ECMA-C30604□S and ECMA-C30804□7 can both be rated at 400 W with a 14 mm shaft. Their frames are 60 and 80 mm respectively. Compare the mounting holes, shaft engagement length and brake option before ordering.

Check feedback in both directions on the bench. With a compatible drive, confirm that its position value changes in the expected direction when the motor reverses. If the machine homes using the Z index, verify that signal too. Enter the result in the maintenance record.

Save the scaling before fitting a spare. Record electronic gearing, the output pulse setting if used, and the home offset from the drive settings. On the first test, command a known distance and measure actual machine travel. Record any difference after reversing direction. This helps determine whether a positioning error comes from scaling or mechanical backlash.

Record where an encoder alarm appears. If it recurs at the same position, inspect the flex points in the cable carrier and the connector locks. If it coincides with power equipment switching on, check shielding and electrical noise.

Observe stopping behaviour and heating under load. If auto-tuning was used, record the axis response and motor temperature during an actual work cycle. Use the relevant manual to check the motor holding brake on vertical axes or the regenerative braking circuit if a bus voltage fault occurs during deceleration.

Delta ECMA 2500 PPR PDF downloads

ASDA-AB User Manual and ECMA Matching Tables · English, November 2014, 343 pages. ECMA codes and matching on PDF pages 17–18, CN2 and four-edge counting on page 69.

ASDA-B User Manual and ECMA Matching Tables · English, June 2009, 321 pages. Motor and drive matching on PDF page 19.

For other documents, visit the Delta Servo Manuals archive.

Related topics and Delta equipment

Servo system FAQs · Delta ECMA motor family · Delta ECMA motors with magnetic encoders · Delta ECMC motors

Manufacturer reference · Delta Electronics ASDA-AB user manual