Delta ECML Linear Motors

Delta ECML Linear Motors

Delta ECML is a series of shaft-type, coreless permanent-magnet synchronous linear motors. The coil generates linear force directly, and the slide and carriage guide the moving load. For precise axis control, select the coil, magnetic shaft, position scale and compatible servo drive as a system.

ECML coil and ASDA-A2R drive combinations

Delta’s A2R catalog lists the following motor and drive combinations. Check the full suffix on the drive nameplate as well.

ASD-A2R-0121-□ · 100 W — ECML-S1606A2DNS, ECML-S1608A2DNS
ASD-A2R-0221-□ · 200 W — ECML-S2003A2DNS, ECML-S2004A2DNS, ECML-S2005A2DNS
ASD-A2R-0421-□ · 400 W — ECML-S2504A2DNS, ECML-S2506A2DNS, ECML-S3204A2DNS
ASD-A2R-0721-□ · 750 W — ECML-S2508A2DNS, ECML-S3206A2DNS, ECML-S3208A2DNS, ECML-S3505A2DNS
ASD-A2R-1021-□ · 1 kW — ECML-S3506A2DNS

Select the coil by force and dimensions. Within the same 400 W drive group, Delta specifies 62.3 N rated force and a 1.00 mm air gap for the ECML-S2504A2DNS, and 87.4 N rated force and a 1.75 mm air gap for the ECML-S3204A2DNS. For load sizing, account for the moving mass of the coil, carriage and workpiece, as well as required acceleration and duty cycle.

Magnetic shaft, Hall sensor and linear scale

ECML-S identifies the coil assembly, and ECML-SM identifies the cylindrical magnetic shaft. The catalog lists Ø16, Ø20, Ø25, Ø32 and Ø35 mm shaft diameters. For example, ECML-SM161000 specifies a Ø16 mm shaft with a nominal length of 1,000 mm. Determine usable travel from the coil length, end clearances and machine travel limits.

The coil’s digital Hall sensor helps determine the electrical phase angle. An internal thermistor monitors winding temperature. A separate linear encoder measures axis displacement. The manual shows the compatible 5 V differential scale input, Hall U/V/W and temperature inputs on CN5. Verify incremental signal resolution and count direction against the feedback configuration and position control setup.

ECML technical documents

ASDA-A2R catalog · ECML selection tables (EN) · Drive combinations on page 10 and coil and magnetic shaft ordering codes on page 13.

ASDA-A2R user manual · ECML specifications (EN) · CN5 wiring on page 3-60, ECML force and air gap tables in section 11.3, and linear motor feedback setup on pages 12-10 and 12-11.

Delta servo PDF archive

Editor’s Note

When buying used, ask to see the coil and shaft from the same axis. Get the coil nameplate, shaft diameter and length, scale and readhead codes, and the drive parameter backup together. During inspection, look for rub marks along the coil path, impact marks on the shaft and crushed moving cables. If a motion trace from the original axis is available, ask under what conditions the fault occurred.

Check the air gap across the whole stroke. If the coil clears one end but rubs at the other, check shaft-to-guide alignment and carriage deflection under load. Mark any position where the symptom repeats. This helps distinguish mechanical vibration and rubbing from a position feedback fault.

Compare scale counts over a known distance. Follow the manufacturer’s safe commissioning procedure and compare the count with an independent position measurement. A reversed count points to direction settings. An error proportional to distance points to scaling. If AL057 occurs at a particular cable position, inspect the readhead, cable carrier and possible signal noise. Then measure home return repeatability.

Observe a cold axis through a production cycle. If force drops over time, record drive current, winding temperature, heat transfer from the coil to the carriage and the actual moving mass. If AL055 appears, follow the motor magnetic field diagnostics in the manual to check agreement between Hall and scale feedback.

Test rapid stops and gain settings separately. If an alarm occurs only during rapid deceleration, review moving mass, stopping time and regenerative braking together. Once the guide and scale are verified, use position error recorded during the actual duty cycle to assess auto-tuning and servo gain.

Related topics

How servo motors work · Speed loop gain · Servo control loops · Electronic gearing · Supervisory control in servo systems

Other Delta units

Delta ASDA-A2R servo drives · Delta AH motion controllers · Delta ECMA rotary servo motors · Delta ECMR · Delta ECMS spindle motors

Delta servo motor category · Used Delta automation equipment

External references

Delta Electronics catalog · Distributor copy of the A2R user manual