Delta ASDA-A3
Delta ASDA-A3 Servo Drive Series
The Delta ASDA-A3 is an AC servo drive series for precise position control and short machine cycles. Each drive controls one servo motor in applications such as labelling, cutting, feeding and transfer. Delta specifies a maximum speed-loop bandwidth of 3.1 kHz. Actual machine response depends on load inertia, mechanical rigidity and tuning.
Model code, power supply and communication
The ASD-A3-0421-L is a 400 W, 220 V class drive. The ASD-A3-1043-E is a 1 kW, three-phase 400 V EtherCAT drive. In the ordering code, 21 denotes 220 V single- or three-phase, 23 denotes 220 V three-phase, and 43 denotes 400 V three-phase. Check the phase, input current and control power using the drive nameplate and wiring diagram for the full model code.
A3-L supports pulse and analogue commands plus RS-485. A3-M adds CANopen to those options. A3-F uses DMCNET and A3-E uses EtherCAT. Delta lists STO for the M and E variants in the 220 V class and for L, M, F and E in the 400 V class. When buying a spare, check both the PLC or motion controller network and the machine safety circuit.
For multi-axis synchronisation, confirm the operating mode and cyclic data mapping supported by the master. On a machine using interpolation, check the project to see where the trajectory is calculated and what units each axis receives. Related Delta DMCNET equipment includes the AH20MC-5A motion module and servo communication accessories.
Matching the motor, encoder and cables
Use the complete motor code when matching the motor and drive. Delta’s manual includes the 400 W ECM-A3L-CY0604RS1 for the ASD-A3-0421 drive class. Its tables also list specific ECM-A3H, ECM-A3L, ECMC and ECM-B3 motor combinations. When sizing the motor, consider inertia, speed, peak torque and brake requirements together.
The encoder type depends on the motor code. A3 matching tables include 24-bit optical and 17-bit magnetic options. CN2 carries motor feedback. On an axis with an external scale, confirm CN5 and full-closed-loop support for the drive variant and firmware. Select power, brake and encoder leads from the Delta servo cable tables. When checking positioning accuracy, measure backlash and homing repeatability too.
ASDA-Soft and initial measurements
Connect through CN4 Mini USB with a compatible version of ASDA-Soft. Read and back up the parameters before changing drive settings. After auto-tuning, monitor commanded position, actual position, speed and torque in the same cycle. When assessing dynamic response under load, record where following error increases and how long the axis takes to settle.
Editor’s Note
Ask for the drive and motor nameplates when buying used equipment. ASD-A3-0421 and ASD-A3-0443 denote the same power rating in different voltage classes. Check the complete drive suffix, connectors and motor brake option against the photos.
Include network communication in the bench test. For EtherCAT, ask for a test showing that the controller discovers the drive, reaches OP and reads position feedback. If the motor runs while the machine still reports the axis as unavailable, start with the ESI file, PDO mapping and status word.
Save the machine’s motion settings before removal. Record motor direction, electronic gearing, home offset and any PR or E-CAM data in use. After loading the backup, command a known distance and measure actual travel. A scaling error can send a part to the wrong position while the axis appears to run normally.
Check for mechanical play if the axis oscillates at standstill. Inspect the coupling, guides and transmission. If the fault recurs at the same cable carrier position, include the encoder lead and plug in the shielding and noise checks. Add the position, load and direction to the maintenance record.
Review deceleration alarms in the context of the cycle. Check the load, stop ramp and regenerative braking circuit together. If the issue appears after several cycles, record motor temperature and cabinet airflow.
Include the safety check when replacing a drive on an STO-equipped machine. Review the CN10 diagram for the full model code, the machine safety circuit and the documented commissioning test together. On a vertical axis, verify the motor holding brake and load retention separately.
Delta ASDA-A3 PDF downloads
ASDA-A3 Servo Drive User Manual · English, 27 February 2025, 1,287 pages. Wiring, drive and motor matching, ASDA-Soft, operating modes, communication and alarm codes.
ASDA-A3 Drive and Motor Technical Catalogue · English, 24 February 2025, 102 pages. Ordering codes, dimensions, motor tables and accessories.
For documentation on other series, visit the Delta Servo Manuals archive.
Related topics and Delta equipment
Servo system FAQs · Delta servo drive series
For other Delta drive documentation, see ASDA-A2, ASDA-A2-E, ASDA-B3 and ASDA-M.
Manufacturer reference · Delta Electronics ASDA-A3 technical catalogue