Delta ECM-A3H
Delta ECM-A3H High-Inertia Servo Motors
The Delta ECM-A3H is a high-rotor-inertia AC servo motor family. Delta lists 50–750 W, a rated speed of 3,000 rpm and a maximum speed of 6,000 rpm for the 220 V class models on this page. For machine applications such as feeding, indexing and transfer, compare the motor’s torque-speed curve with the actual load and cycle time.
Motor codes, power and frame sizes
40 mm frame · ECM-A3H-C□040F□S1 (50 W) and ECM-A3H-C□0401□S1 (100 W).
60 mm frame · ECM-A3H-C□0602□S1 (200 W) and ECM-A3H-C□0604□S1 (400 W).
80 mm frame · ECM-A3H-C□0804□71 (400 W, 14 mm shaft) and ECM-A3H-C□0807□S1 (750 W).
Both 400 W models have a rated torque of 1.27 N·m. Delta’s manual lists a rotor inertia of 0.45 × 10⁻⁴ kg·m² for the 0604 without a brake and 0.92 × 10⁻⁴ kg·m² for the 0804 without a brake. When sizing the motor, assess reflected load inertia, acceleration and settling time together. Coupling backlash and mechanical stiffness also affect positioning accuracy.
Encoder, brake and shaft codes
In ECM-A3H-CY0604RS1, H denotes high inertia, C the 220 V and 3,000 rpm class, and Y an optical absolute encoder. The Y-type encoder has 24-bit single-turn resolution and 16-bit turn counting. Delta also lists 1 and 2 for 24-bit incremental options with single-turn absolute capability. Check drive feedback support using the full motor code.
In this example, R denotes a keyed shaft with a tapped hole, an oil seal and no brake. An S in that position denotes the oil-sealed version with a brake. In the next position, S specifies the standard shaft and connectors, while 7 specifies the special 14 mm shaft on the 80 mm, 400 W model. Match the power, brake and encoder cables using the motor and drive drawings.
ASDA-A3 drive combinations
Delta’s 2025 user manual pairs 0604 and 0804 motors with the 400 W ASD-A3-0421 class and the 0807 motor with the 750 W ASD-A3-0721 class. The 2025 catalogue shows the same combinations. Check the full servo drive code and communication option in the ASDA-A3 model table.
Delta’s two tables list different combinations for 100 W and 200 W. PDF page 34 of the user manual lists the 0121 class for the 100 W 0401 motor and the 0221 class for the 200 W 0602 motor. PDF page 18 of the catalogue lists 0221 and 0421, respectively. Confirm the motor and drive combination with Delta or an authorised distributor using the full codes before ordering either model.
Editor’s Note
Check whether the 400 W motor is a 0604 or an 0804. When buying used, ask for photos of the nameplate, flange, shaft length and sockets. The two motors share a power rating but have different frames, rotor inertia and mounting dimensions. Add the full removed motor code to the machine’s maintenance record.
Check how the machine uses the motor brake. On vertical axes, verify load retention at standstill and the machine’s brake release sequence. If a DC bus overvoltage alarm occurs during deceleration, review the regenerative braking circuit together with the load and stop ramp.
Record the settings and home reference before removal. Save the motor direction, home offset and electronic gear ratio from the drive parameters. After replacement, command a known position and measure actual travel. Check the units used by the PLC position command as well.
Observe a real work cycle after tuning. If you use auto-tuning, record the position command, actual position and torque in the same cycle. Measure axis settling under load. If the motor heats up over several cycles, record motor temperature together with cycle time.
Inspect the cable carrier if a feedback alarm recurs at one position. Check the connector latch, the cable flex point and the shield connection. If the fault coincides with power equipment switching on, inspect the power and signal routes for electrical interference.
Delta ECM-A3H PDF downloads
ASDA-A3 Technical Catalogue and ECM-A3H Motor Data · English, 24 February 2025, 102 pages. Ordering codes on PDF page 39 and motor specifications on pages 42–43.
ASDA-A3 User Manual and ECM-A3H Matching Tables · English, 27 February 2025, 1,287 pages. 220 V combinations on PDF page 34 and high-inertia motor specifications in Appendix A.2.2.
For documents on other series, visit the Delta Servo Manuals archive.
Related topics and Delta equipment
Servo system FAQs · Delta servo motor families
For other Delta motor documentation, see ECM-A3L low-inertia motors, ECMA and ECMC.
Manufacturer reference · Delta Electronics ASDA-A3 technical catalogue