Delta ECM-A3L

Delta ECM-A3L Low-Inertia Servo Motors

Delta ECM-A3L is a low-inertia servo motor family rated from 50 to 750 W in 40, 60 and 80 mm frame sizes. In this group, C identifies the 220 V class and a rated speed of 3,000 rpm. Delta’s matching table lists a maximum speed of 6,000 rpm. For short-cycle feeding and positioning applications, select the motor with the load inertia and servo drive in mind.

Frame sizes, power ratings and ASDA-A3 drive pairings

40 mm frame · ECM-A3L-C□040F at 50 W and ECM-A3L-C□0401 at 100 W. The 2025 catalogue lists both with the ASD-A3□-0121-□.

60 mm frame · ECM-A3L-C□0602 at 200 W with ASD-A3□-0221-□. ECM-A3L-C□0604 at 400 W with ASD-A3□-0421-□.

80 mm frame · ECM-A3L-C□0804 at 400 W with ASD-A3□-0421-□. ECM-A3L-C□0807 at 750 W with ASD-A3□-0721-□.

Boxes indicate positions in a model pattern. Verify the motor and drive pairing using the complete order codes. Check flange and shaft dimensions when selecting a motor. For continuous operation, check the working point on the motor’s torque–speed curve.

Encoder, brake and connector codes

In ECM-A3L-CY0604RS1, L means low inertia, Y identifies a 24-bit optical absolute encoder, 06 indicates a 60 mm frame and 04 indicates 400 W. R denotes an oil seal without a brake, and S in the same position denotes an oil seal with a brake. The S in the following position identifies the standard shaft and connector option.

Delta also specifies single-turn absolute operation for the 1 code, a 24-bit optical incremental encoder. Before replacement, check the feedback type, CN2 cable and the machine’s closed-loop settings against the complete motor code.

Editor’s Note

1. Specify the frame and shaft separately on a 400 W quote. The 0604 has a 60 mm frame and the 0804 has an 80 mm frame. The 2022 catalogue shows □71 for the 0804, and the 2025 catalogue shows RS1/SS1. For a used motor inspection, request a nameplate photo and a measured shaft diameter. Check the bolt pattern, pilot diameter and keyway against the drawing.

2. Review tuning when changing between motors of the same power. The 2025 catalogue lists rotor inertias of 0.150 and 0.352 × 10⁻⁴ kg·m² for the brakeless 0604 and 0804 respectively. Include the load inertia. Monitor settling time and repeatability when checking positioning accuracy.

3. Order cables by connector and exit direction. Photograph the motor-side power and encoder connectors separately. Check the cable exit direction and suitability for a moving cable carrier. If feedback drops out, check grounding, shield termination and encoder cable routing.

4. Save the axis settings before removing the motor. Record the drive configuration, the electronic gear ratio if used, and the homing method. On an absolute axis, preserve the reference value. After replacement, check actual axis travel against a known position command.

5. Test the brake separately on a brake-equipped axis. On a vertical axis, verify brake release and holding after securing the load according to the machine procedure. Check travel direction and the limit switches during a controlled low-speed test. Then review loop gains and auto-tuning.

6. Record the duty cycle on axes that stop frequently. Note the start frequency, load and deceleration time. If a fault involves regenerative energy, check the braking resistor against the exact ASDA-A3 drive model.

ECM-A3L technical documents

2025 ASDA-A3 Catalogue — ECM-A3L Matching Table (PDF) · English, 102 pages. The motor and drive table is on PDF page 18, and the torque–speed curves are on page 44.

2025 ASDA-A3 User Manual (PDF) · English, 1,287 pages. See pages 29–30 for motor codes, page 34 for pairings and page 1209 for shaft and mounting dimensions.

2022 ASDA-A3 Catalogue — Earlier ECM-A3L Codes (PDF) · English, 52 pages. PDF page 19 shows the 0804□71 pattern for the 80 mm, 400 W motor.

Related Delta equipment

Delta ASDA-A3 drives · ECM-A3H high-inertia motors · ASDA-A2 · ECMA · ECMC · ECML linear motors

Servo cables · Encoder connectors · Power connectors · Delta AS PLC · Delta AH motion controllers

Delta Servo Motors · Used Servo Drives · Delta Servo Manuals

External reference — Delta’s ECM-A3L matching table