Delta CANopen cables
Delta CANopen cables
Delta CANopen cables are ready-made connection cables for CANopen links between suitable PLCs, motion controllers and drives. The UC-CMC…-01A models in this group have RJ45–RJ45 connections and come in several lengths. They carry communication signals and do not perform protocol conversion or controller functions. See Delta PLC accessories and Delta DVP PLC series for related hardware.
UC-CMC…-01A models and lengths
Delta UC-CMC003-01A: 0.3 m · Delta UC-CMC005-01A: 0.5 m · Delta UC-CMC010-01A: 1 m.
Delta UC-CMC015-01A: 1.5 m · Delta UC-CMC020-01A: 2 m · Delta UC-CMC030-01A: 3 m.
Delta UC-CMC050-01A: 5 m · Delta UC-CMC100-01A: 10 m · Delta UC-CMC200-01A: 20 m.
Select length from the actual cable route through the cabinet, allowing for duct bends and necessary service slack. A 20 m cable alone does not establish that the network will operate over that distance at every speed. Check total trunk length, drop lengths and communication rate together.
Device and port compatibility
Delta's cable selection guide shows UC-CMC…-01A cables in Delta DVP10MC11T and selected Delta DVP-PM CANopen applications. These examples do not establish compatibility with every Delta CPU or servo drive. Check the complete device models, CANopen support and port pin assignments at both ends.
An RJ45 socket does not necessarily carry Ethernet. A controller may have separate CANopen and Ethernet ports, so use the port label and hardware diagram when connecting the cable. Do not treat an ordinary network cable as interchangeable solely because its plug fits. For EtherCAT connections, consult Delta EtherCAT cables separately.
CANopen termination and distribution
Provide termination at the two physical ends of the CANopen trunk. Delta's TAP-TR01 is a 121 Ω termination plug for applicable RJ45 CANopen connections. Account for resistors already enabled in devices or distribution boxes; do not add termination at every node.
Where drop connections are required, suitable distribution hardware such as Delta TAP-CN03 may be used. Follow the manufacturer's permitted topology and length limits for trunk and drop wiring. These components are covered under Delta DVP other accessories.
Editor's Note
Before blaming a PLC or servo communication board, record the cable's complete code and the ports it connects. Compare it with a known-good cable of the same model where possible. Photograph connections before removing them so troubleshooting does not introduce another wiring error.
Disconnect both ends before checking continuity and conductor-to-conductor shorts with power removed. Passing a basic cable tester does not prove reliable communication under operating conditions. Compare pin continuity with the correct diagrams for the cable and connected equipment.
If opening a cabinet door or moving the cable changes the fault, inspect connector exits, crushed sections and broken latches. Remove tight bends and strain on plugs. Continuous-flex suitability for a moving axis requires separate confirmation; a cable length code does not establish that rating.
For intermittent CAN failures, check node addresses, a common communication rate and termination at both ends in sequence. Avoid changing the cable, address and speed together. After each step, monitor diagnostic records and communication status to identify which change affected the fault.
When buying a used cable, request close photographs of both plugs as well as the label. Look for bent contacts, loose housings and repaired sections. Where possible, complete the check by establishing communication with the intended equipment; appearance alone does not establish cable condition.
PDF manuals, wiring and network configuration
Use Delta PLC accessories files for cable selection and wiring documents, and Delta PLC and HMI manuals for device port definitions. The passive cable itself does not require software loading; network settings belong to the connected devices. For supported projects, verify Delta CANopen Builder against the CPU and communication module in use.
Related topics
Delta industrial network cables · Delta network connectors · Delta DVP communication cables · Delta DVP programming cables
Return to Delta PLC accessories. Browse controllers in the Delta PLC category and available equipment under second-hand Delta products.
External references: Search the Delta Download Center using the complete model code for manufacturer documentation.