Delta DVP10MC11T

Delta DVP10MC11T – 16-Axis CANopen Motion Controller

The Delta DVP10MC11T is a DVP-MC controller for up to 16 real axes over CANopen. It integrates a PLC and a motion control section. Electronic camming, electronic gearing, flying shear and rotary cutting functions suit packaging, printing and cutting automation.

Power, local I/O and motion network

The controller uses 24 V DC (20.4–28.8 V DC). It has 8 digital inputs, 4 NPN transistor outputs and a 9-pin D‑sub encoder connector. Check PNP/NPN sensor wiring and the encoder output signal against the terminal diagrams. Keep motion-network cables away from motor power leads in the control panel and follow Delta’s grounding diagram.

Use a CANopen-capable servo drive for the motion network. Delta shows a CN6 connection for the -M models of the ASDA-A2 family. Match node addresses, axis assignments and baud rate to the project. Delta’s 2019 CANopen cable selection guide lists the UC-CMC030-01A. The operating manual shows TAP-CB03/05/10 cables and TAP-TR01 termination at both ends of the bus.

PLC program, motion project and PC cables

For PLC logic, use WPLSoft or ISPSoft for PLC programming. Set up the ISPSoft connection in COMMGR. Connect the PC to the COM1 RS‑232 port with the UC-PRG020-12A cable (2 m). Delta also shows the UC-MS020-01A with a suitable USB-to-RS‑232 adapter.

Use CANopen Builder for the motion program, axis parameters, CANopen setup and cam profiles. Connect the PC through the controller’s Ethernet port. Delta’s cable guide lists UC-PRG030-20A (3 m RJ45 to RJ45). Check the port label when connecting the Ethernet cable. The Ethernet port also supports monitoring via Modbus TCP.

COM2 RS‑485 is a shared communications port for the PLC and motion sections. The manual requires a different station address for each section when accessed over RS‑485. Match the Modbus RTU settings to the connected HMI or SCADA project.

Synchronous cutting application

On a continuous-feed line, the master axis position can serve as a reference for the cutter. An electronic cam changes the servo motor’s speed and position through the cutting zone. For position control, first check axis directions and scaling at low speed. Then test the synchronised move.

Related models

The DVP15MC11T supports up to 24 real axes over CANopen Motion. The DVP50MC11T supports EtherCAT motion. See the DVP10PM00M for pulse-based positioning and the DVP16SP11T for right-side digital I/O expansion. Check network type, drive family and project compatibility when replacing a controller.

Editor’s Note

When buying used, ask for photos of the full label and both the CANopen and Ethernet ports.

Back up the PLC and motion projects separately before replacement. Check the axis settings and cam tables as well.

If a drive stays offline, check its node address, baud rate and the termination at both ends of the bus.

Run the first test at low speed with one axis. Record its direction, reference position and alarm status.

When assessing a spare controller, verify the COM1 connection and test CANopen communications with an actual drive.

PDFs and technical documents

Related document index Delta DVP PLC files. The DVP-MC operating manual covers ports in Section 2.1.1 and the ASDA-A2 connection in Section 3.2.2. The instruction sheet includes terminal and wiring information in English and Turkish. See Sections 1.12 and 3.1.1 of the Delta PLC/HMI Cable Selection Guide for cables.

DVP10MC11T main page · DVP PLC series · Delta PLC accessories · Delta external terminals · Delta PLC · Used Delta models · Delta PLC and HMI manuals

Delta AS PLC · Delta AH PLC · Delta AH external terminals · Delta TP panels and remote I/O

External references

Delta DVP-MC Instruction Sheet (2010, TR/EN) · Delta DVP-MC Operating Manual (2015) · Delta PLC/HMI Cable Selection Guide (2019)