Delta UC-CMC010-01A
Delta UC-CMC010-01A — 1 m CANopen / DMCNET RJ45 Cable
Delta UC-CMC010-01A is a 1-metre communication cable with RJ45 connectors at both ends. It belongs to the Delta CANopen cables range. The AS accessory catalogue lists UC-CMC cables for suitable CANopen, DeviceNet and DMCNET connections. Confirm the application against the connected equipment’s port definitions and wiring diagrams.
Application and compatibility
The AS hardware manual lists UC-CMC010-01A among the CANopen cables for the AS-FCOPM family. For a Delta AS PLC application, check device addresses, data rate and network layout alongside cable selection. CANopen Builder can be reviewed for network configuration; the cable itself does not receive software.
UC-CMC010-01A does not convert protocols. An RJ45 connector alone does not establish Ethernet or EtherCAT compatibility. Delta EtherCAT cables have their own connection requirements. On a DVP PLC or another device, select the cable using the port specification rather than connector shape alone.
Pin functions in the manufacturer guide
The table below follows page 3-9 of the Delta cable selection guide dated 2019-08-15. “—” means no assigned signal in that drawing.
| Pin | CANopen | DMCNET |
|---|---|---|
| 1 | CAN+ | DMCNET_D1+ |
| 2 | CAN− | DMCNET_D1− |
| 3 | CAN_GND | DMCNET_D2+ |
| 4 | — | — |
| 5 | — | — |
| 6 | CAN_SHLD | DMCNET_D2− |
| 7 | CAN_GND | DMCNET_GND |
| 8 | — | DMCNET_GND |
Read pin numbers using the connector view in the equipment manual. The CANopen and DMCNET columns describe separate applications. This table does not establish a DeviceNet pinout or permission to apply power to reserved pins.
Installation and network checks for a 1 m cable
Measure the 1 m cable length along its intended route. Include duct routing, bends and access clearance in addition to the direct distance between sockets. Do not pull on the connector to make the cable reach or leave a sharp bend at the cable entry.
Assess total network distance together with protocol, data rate, trunk and branch layout. DeviceNet installations have separate individual and cumulative drop limits. A one-metre cable alone does not establish compliance of the entire network. Compare other network cables such as UC-DN01Z-01A and UC-DN01Z-02A against their own connection requirements.
Distribution and termination accessories
Review TAP-CN03 for RJ45 distribution connections, and TAP-CN01 or TAP-CN02 for terminal connections. Verify each accessory’s port type and network role. Arrange any required network power according to the equipment diagram.
Suitable CANopen termination accessories include TAP-TR01. Determine termination points from the trunk ends and existing device switches. For DMCNET, follow the relevant system manual.
Length options in the same family
| Model | Length |
|---|---|
| UC-CMC003-01A | 0.3 m |
| UC-CMC005-01A | 0.5 m |
| UC-CMC010-01A | 1 m |
| UC-CMC015-01A | 1.5 m |
| UC-CMC020-01A | 2 m |
| UC-CMC030-01A | 3 m |
| UC-CMC050-01A | 5 m |
| UC-CMC100-01A | 10 m |
| UC-CMC200-01A | 20 m |
Choose a length that permits easy connector access without cable tension. Compare other connection types under Delta industrial network cables.
Editor’s Note
Read the middle of the model code carefully: CMC010 is one metre; CMC100 is ten metres. Confusing these codes can leave the cable too short or create unnecessary excess inside the panel.
Measure the actual duct route rather than estimating one metre by eye. Include room to connect and disconnect the plugs. Stretching a short cable can eventually cause intermittent contact at an otherwise sound connector.
Switch off power and disconnect both ends before measurement. Check continuity and unintended shorts against the correct diagram. Do not map every conductor as if this were a standard Ethernet cable.
If communication drops out, inspect the latches, connector entries and any crushed sections first. Then check device addresses, data rate and termination in sequence. Changing several settings together makes the cause harder to trace.
Routing matters even for a short cable. Avoid unnecessary proximity to power cables and contactors, and follow the equipment manual for shield connections. Pay particular attention to splices or replaced connectors.
For a used cable, continuity alone is insufficient. Request real data exchange and stable operation with suitable devices. Begin by monitoring status and communication data before issuing any motion commands.
PDF and related topics
Use the Delta PLC accessories PDF and software files page for connection documents. Other references are available under Delta PLC and HMI manuals and Delta user manuals.
Navigation: UC-CMC010-01A main page · Delta PLC accessories · Delta PLC models · Used Delta products
External references
Delta PLC/HMI Cable Selection Guide — 2019-08-15, 3-9 / 4-4 · Delta AS / AX-3 Catalogue — UC-CMC Cable Accessories · Delta AS Hardware and Operation Manual — AS-FCOPM Cables · ODVA — DeviceNet Cable System Planning and Installation