Delta UC-CMC003-01A
Delta UC-CMC003-01A 0.3-Metre CANopen Cable
Delta UC-CMC003-01A is a 0.3-metre / 30 cm CANopen communication cable with RJ45 connectors at both ends. It belongs to Delta CANopen cables and Delta PLC accessories. It can be considered for nearby compatible devices; select the length according to the actual route between their ports.
Applications and device compatibility
The DVP catalogue associates the UC-CMC family with CANopen products including DVP10MC11T, DVP15MC11T, DVPCP02-H2, DVPCOPM-SL and TAP-CN03. This listing does not mean that every device has a direct RJ45 socket; terminal-based ports require an appropriate connector or distribution arrangement.
The manufacturer's cable guide also lists UC-CMC003-01A for DMCNET connections between AH20MC-5A and suitable ASD servo drives. The cable does not convert protocols; the connected devices' port specifications determine the network used.
UC-CMC003-01A and UC-EMC003-02A belong to different cable groups. The UC-EMC model is listed under Delta EtherCAT cables. Equal length and RJ45 appearance do not make CANopen, DMCNET and EtherCAT ports interchangeable.
Pin assignments and connection checks
The guide's 2019-08-15 edition, Figure 1 / printed page 3-9 gives these CANopen assignments: 1: CAN+, 2: CAN-, 3 and 7: CAN_GND, 6: CAN_SHLD. Pins 4, 5 and 8 are unassigned in that table. For DMCNET, pins 3 and 6 form the second data pair.
Read pin numbers from the specified connector viewing direction and compare the connected device's diagram. When fitting Delta network connectors, do not wire replacement ends solely by conductor colour or a conventional Ethernet colour sequence.
Installing a 30 cm cable and checking the network
A 0.3-metre cable does not establish a usable 30 cm straight gap between devices. Plug orientation, cable-duct bends and clearance at each cable entry affect the route. Install the cable without tension or sideways loading on the sockets.
In a project using TAP-CN03, check trunk and drop connections against the existing network drawing. Adding this short section does not remove the need to assess total line length, baud rate and drop layout.
Assess CANopen termination at the two physical network ends. Account for TAP-TR01, distribution-box termination switches and existing device resistors together. Do not add a separate terminator between every 30 cm cable section.
Length options and software
If the route cannot accommodate a 30 cm cable, consider UC-CMC005-01A at 0.5 metres, UC-CMC010-01A at 1 metre or UC-CMC020-01A at 2 metres. UC-CMC030-01A is 3 metres long; distinguish 003 from 030 when ordering.
No software or firmware is installed in UC-CMC003-01A. Configure node addresses, baud rate and data mapping in the connected devices. Use Delta CANopen Builder according to the engineering tools supported by the controller or communication module.
Editor's Note
This cable is 30 centimetres long. A label showing 030 instead of 003 identifies the three-metre model. Order by the complete code rather than selecting only by the connector in a photograph.
Even adjacent devices can have ports facing opposite directions. Do not stretch the cable to make it reach. The latch should engage without the cable pulling on the socket; choose the next suitable length if necessary.
Inspect a used cable's latch, contacts and plug entries. Disconnect both ends before continuity testing, then gently move each cable entry while measuring to find intermittent breaks.
A satisfactory continuity measurement does not prove reliable communication under all operating conditions. Test data exchange with suitable devices and observe whether communication drops when motors run. Compare the result with a known-good cable.
If communication fails, check port selection, node addresses, baud rate and termination first. Keep the short cable clear of power wiring and avoid pinching it. Hold the plug body when disconnecting rather than pulling the cable.
PDF and software documentation
Use Delta PLC accessories files for wiring resources and Delta PLC and HMI manuals for device settings. The manufacturer's PLC/HMI cable guide lists applications on printed page 3-7 and the UC-CMC connection drawing on page 3-9. Check the document edition together with your device's wiring diagram.
Related topics
Delta CANopen cables · Delta UC-CMC005-01A · Delta UC-CMC010-01A · Delta UC-CMC020-01A · Delta UC-CMC030-01A · Delta TAP-CN03
Return to Delta PLC accessories. Browse controllers in the Delta PLC category and available equipment under second-hand Delta products.
External references: Delta PLC/HMI Cable Selection Guide (archived manufacturer document) · Delta Download Center