Delta UC-ET030-24D
Delta UC-ET030-24D Shielded I/O Terminal Cable
Delta UC-ET030-24D is a 3-metre shielded cable connecting a PLC I/O module to external terminal units. It branches from one MIL IDC40 connector to two IDC20 connectors. It belongs to Delta DVP / AH I/O cables and Delta PLC accessories. The connection carries the module's field input/output signals to terminal units.
DVP32SN11TN and two relay terminal units
The manufacturer's DVP catalogue specifies the pairing DVP32SN11TN ↔ UB-10-OR16A. The cable selection guide shows the module's 40-pin connector feeding two separate 16-channel relay terminal units. The terminal units provide the relay function; the cable carries signals to them.
Consult Delta external terminals, Delta DVP Slim digital modules and Delta DVP expansion modules when selecting the assembly. In a Delta DVP PLC system, match output addresses, module placement and external terminal power connections to their respective instructions.
Checking the 40-pin and two 20-pin connections
The IDC40 end connects to the module, while the two IDC20 branches connect to the corresponding terminal units. Follow the drawing for channel groups, pin 1 orientation, connector keys and common connections. Interchanging branches can send an output command to a different field channel. Label both branches and terminal groups before removal.
The manufacturer's guide identifies UC-ET030-24D as a shielded cable under Figure 4B. Connect its shield according to the device and panel wiring design. Shielding does not correct terminal-supply or load-circuit wiring faults.
24D, 24B and 24C distinctions
UC-ET010-24D is the 1-metre shielded IDC40-to-two-IDC20 option; UC-ET020-24D is the 2-metre option. UC-ET030-24D has a specified length of 3 metres. Plan the cabinet route accordingly.
UC-ET030-24B is also 3 metres long and shielded, but uses IDC40-to-IDC40 connections. The manufacturer lists that group for different terminal arrangements involving UB-10-OT32A and UB-10-ID32A. UC-ET010-24C is a 1-metre IDC40-to-two-IDC20 option that the catalogue does not identify as shielded. Preserve the complete suffix when selecting a replacement.
Exact module selection in AH applications
The cable selection guide lists UC-ET030-24D for AH32AN02T-5C with UB-10-OR16A and AH32AN02P-5C with UB-10-OR16B. Although the cable is shared, the terminal model changes with the module's output arrangement. Preserve this distinction when selecting Delta AH external terminals.
No program, driver or IP configuration is loaded into this cable. Commissioning checks concern I/O addresses, channel mapping, terminal power and field loads. Connector count and cable length do not establish permissible electrical loading.
Editor's Note
Specify the complete UC-ET030-24D code together with the module and both terminal models. The equally long 24B cable does not have the same two-branch arrangement.
Label both 20-pin branches and record their destinations before removal. After replacement, verify that each channel reaches the intended relay; connector fit alone does not verify channel mapping.
Disconnect the cable from all devices before continuity testing. Follow the manufacturer's diagram for signals and commons, keeping shield connections distinct. Inspect IDC connectors for bent pins, loose latches and cable-entry damage.
If one branch works and the other does not, check that branch's 20-pin plug, terminal supply and channel group first. Narrow the fault to the cable, module or terminal before changing the PLC program.
If a relay operates but the field load does not, check its contacts, load supply and field wiring separately. Route the cable away from motor power wiring and prevent strain at the branch point. Test a used cable by checking channels individually.
PDF and wiring documentation
Use Delta PLC accessories files for the cable selection guide and accessory resources. Consult Delta PLC and HMI manuals for module and terminal instructions. The guide shows the DVP arrangement on printed pages 2-2 and 2-17, and the Figure 4B cable drawing on page 2-32.
Related topics
Delta UC-ET010-24D · Delta UC-ET020-24D · Delta UC-ET030-24B · Delta UB-10-OR16A · Delta DVP32SN11TN
Return to Delta DVP / AH I/O cables. Browse controllers in the Delta PLC category and available devices under second-hand Delta products.
External references: Delta PLC/HMI Cable Selection Guide (archived manufacturer document) · Delta Download Center