Delta UC-ET010-24C

Delta UC-ET010-24C

Delta UC-ET010-24C is a 1-metre ribbon-style I/O external-terminal cable that branches from one IDC40 connector to two IDC20 connectors. It connects a compatible PLC output module to external terminal boards. Select it by cable length, connector arrangement and the exact module-to-terminal combination.

DVP32SN11TN and two terminal boards

Delta's connection drawing shows the Delta DVP32SN11TN module connected through UC-ET010-24C to two Delta UB-10-OR16A relay terminal boards. The IDC40 end connects to the module, while the two IDC20 branches connect to separate boards. Follow the drawing to identify the output group carried by each branch.

40 contacts do not mean 40 independent outputs. Channel count, common connections and supply pins depend on the module pin arrangement. The cable carries the connections; the relay interface is provided by the terminal board. Review board options under Delta external terminals.

OR16A and OR16B selection for AH modules

The manufacturer specifies UB-10-OR16A for Delta AH32AN02T-5C and Delta UB-10-OR16B for Delta AH32AN02P-5C. UC-ET010-24C is listed among the cable options for both arrangements. Check the module's T/P suffix together with the terminal's A/B suffix.

Read the complete board code when selecting from Delta AH external terminals. Similar-looking connectors do not establish electrical compatibility. For another AH model, verify that model's manufacturer connection drawing separately.

Selecting 24C, 24D or 24A/24B

Shielded options with two IDC20 branches are listed as 1 metre for Delta UC-ET010-24D, 2 metres for Delta UC-ET020-24D and 3 metres for Delta UC-ET030-24D. The manufacturer's drawing shows UC-ET010-24C as a 1-metre ribbon assembly.

Delta UC-ET010-24A and Delta UC-ET010-24B use an IDC40-to-IDC40 arrangement; Delta UC-ET030-24B is the 3-metre shielded option with that connection format. Establish whether the terminal side requires one IDC40 or two IDC20 connectors before ordering.

Installation and commissioning

Include duct turns, connector exits and maintenance access when assessing the 1-metre route. Avoid trapping the ribbon under covers or folding it sharply beside a connector. Label both branches clearly through to their terminal boards.

Install with module and field supplies disconnected. Check pin-one orientation, connector keying and retainers. Route the cable away from motor and drive power wiring. Obtain channel-current, common-connection and field-supply limits from the connected hardware's documentation.

Review DVP hardware under Delta DVP expansion modules alongside the supply arrangement under Delta DVP power supplies. After replacing the cable, verify terminal power and output groups. Start with one channel, then check every channel used by the application.

Manuals and connection drawings

Start document selection at Delta PLC accessories files. In the PLC/HMI Cable Selection Guide, printed page 2-2 / PDF page 101 shows the DVP arrangement, printed page 2-17 / PDF page 116 gives the selection table, and Figure 4A, printed page 2-31 / PDF page 130 shows cable construction. Printed page 49 / PDF page 50 of the 2023 DVP/TP catalogue provides the length and connector specification.

Editor's Note

Mark both branches before disconnecting anything. Record the module, cable and terminal labels together. This avoids having to guess which branch serves which output group during reassembly.

Inspect bends carefully on a used cable. Look for cut insulation, crushing and separation at IDC housings. Disconnect using the housing and retainers rather than pulling on the ribbon.

If one branch fails, check that terminal board's power first. Inspect common connections and connector seating too. A group of outputs disappearing together does not by itself establish a PLC fault.

Measure continuity with every cable end disconnected from equipment. Use the viewing direction shown in the manufacturer's drawing. Do not assume a simple one-to-one cable arrangement when tracing pins across the two branches.

During the final check, observe the PLC output command together with terminal and load response. Start with one channel and a controlled test load. Verify that each output group reaches the intended board before returning the machine to its normal cycle.

Related topics

Browse parent groups under Delta DVP / AH I/O cables and Delta PLC accessories, and device documentation under Delta PLC and HMI manuals.

External references: Delta PLC/HMI Cable Selection Guide — 2019 · Delta DVP/TP manufacturer catalogue — 2023 · Delta AH manufacturer catalogue — 2024.