Delta UC-MS030-01A
Delta UC-MS030-01A RS-232 Programming and Communication Cable
Delta UC-MS030-01A is a 3-metre communication cable connecting the RS-232 port of compatible Delta DVP PLC equipment to a computer or suitable serial device. It has an 8-pin male mini-DIN connector at the PLC end and a female DB9 connector at the other end.
Within the DVP communication cable range, this model is used particularly for programming and maintenance through a computer's RS-232 interface. Specify the complete UC-MS030-01A code when ordering; similar cable names can identify different connectors and connection tasks.
Port and equipment compatibility
Delta's cable selection guide shows UC-MS030-01A for COM1 RS-232 connections on relevant models in the DVP-SS2, DVP-SA2, DVP-SX2, DVP-SV2 and DVP-EH3 groups. Check the complete CPU code and intended port separately.
A PLC can have several communication interfaces. Read the port label and consult the relevant connection page before wiring. For an HMI or TP connection, also check the other device's connector and signal arrangement.
Manufacturer's pin assignments
Mini-DIN pin 4 RX ↔ DB9 pin 3 TX; mini-DIN pin 5 TX ↔ DB9 pin 2 RX; mini-DIN pin 8 GND ↔ DB9 pin 5 GND. These connections pair the receiving and transmitting signals.
The DB9 drawing also shows bridges between 7–8 and 1–4–6. Include these groups in continuity checks. Distinguish the connector mating face from its solder-side view and follow the orientation in the manufacturer's drawing.
Mini-DIN pins 1 and 2 are labelled 5V, with no connection drawn from them to DB9. When repairing a cable, follow pin numbers rather than assuming that matching wire colours establish the correct connections.
Computer connection and software
With a suitable RS-232 port on the computer, connect the female DB9 end to that interface. A USB-only computer requires a USB/RS-232 converter; check its driver and assigned COM number. For an integrated USB connection, also review UC-PRG020-12A.
When using CPU-supported WPLSoft or ISPSoft, match the port number, communication speed and data format to the existing PLC settings. Do not infer one default speed for every CPU from the cable model.
Begin with a connection check or device identification read that leaves the existing program intact. Prepare the machine for maintenance and back up the current project before downloading a program.
Differences from similar cables
UC-MS020-01A is the 2-metre option. UC-MS010-02A is a 1-metre model with a 90-degree mini-DIN connector. Consider cable routing and available clearance in the cabinet.
UC-MS030-06A is 3 metres long and UC-MS020-06A is 2 metres; the manufacturer's selection guide shows both with a male DB9 connector. The female DB9 end of UC-MS030-01A is an important ordering distinction.
Evaluate other serial cable models, including UC-PRG030-10A and DVPACAB230, against their own diagrams. A connector fitting physically does not by itself establish the correct pin arrangement.
Editor's Note
Check the DB9 end before ordering. Male and female connectors can make the difference between a straightforward repair and a delayed service visit. Photograph both cable ends, the label and the device port together.
Disconnect the cable from both devices before continuity testing. Check the 4–3, 5–2 and 8–5 connections, then compare the DB9 bridges with the diagram. Gently flex the cable near each connector while measuring to investigate intermittent internal breaks.
Verify the USB converter separately where one is used. If the same cable worked on an older computer, check the new computer's COM number, driver and whether its converter provides a genuine RS-232 interface.
Never force the mini-DIN plug. A bent pin or damaged locating feature can also damage the PLC socket. Hold the connector body, align it carefully and avoid pulling on the cable when disconnecting.
A clean outer jacket does not establish the condition of a used cable. Taped joints, replacement DB9 shells and loose solder joints can cause intermittent faults. Request both pin checks and a communication test with a known working PLC.
Repeat the connection check before finishing. Reconnect several times, read device identification again and ensure that cabinet doors cannot trap the cable. Record the final settings and COM number in the maintenance notes.
PDF diagrams and software
Use our Delta PLC accessories PDF and software files page for documents. The UC-MS030-01A diagram appears in the Delta PLC/HMI Cable Selection Guide, section 1.22, Figure 2, printed page 1-80. Also check the CPU connection page in that guide.
Related subjects
For other options, see DVP programming cables, DVP communication cables, Delta PLC accessories and used Delta PLC models.
Navigation: Used Delta products | Delta PLC models | PLC accessories | Communication cables | PDF and software files
External references
Delta PLC/HMI Cable Selection Guide | Delta DVP/TP catalogue, accessories | Delta Turkey 2024 archive catalogue, communication cable diagrams