Delta DVPACAB230

Delta DVPACAB230 RS-232 Programming and Communication Cable

Delta DVPACAB230 is a 3-metre RS-232 communication cable connecting compatible Delta DVP PLC equipment to a computer or suitable operator panel. The PLC connection uses an 8-pin mini-DIN connector.

Delta's accessory catalogue lists DVPACAB230 for 9-pin and 25-pin D-SUB computer connections. Some older TP documents also show it without DB25, so verify the label and actual connectors together, particularly when buying used.

Applications and port selection

Earlier DVP-ES, DVP-EX and DVP-SS manuals list DVPACAB230 among cables connecting a PLC to a computer or HMI. The TP04G-AL/AL2 document also shows it for panel-to-DVP PLC communication.

Programming a panel from a computer and connecting that panel to a PLC are different connections. Identify the two devices and check both ports. Matching D-SUB or mini-DIN shapes alone do not establish the correct electrical interface or pin assignment.

RS-232 pin connections

DB9 end: pin 3 TX → mini-DIN 4 RX; pin 2 RX ← mini-DIN 5 TX; pin 5 GND ↔ mini-DIN 8 GND.

DB25 end: pin 2 TX → mini-DIN 4 RX; pin 3 RX ← mini-DIN 5 TX; pin 7 GND ↔ mini-DIN 8 GND. Note that TX, RX and GND use different pin numbers on DB9 and DB25.

The TP04G-AL/AL2 manufacturer drawing shows bridges between DB9 pins 7–8 and 1–4–6, and between DB25 pins 4–5 and 6–8–20. Include these groups when checking a repaired cable. Match connector orientation before reading pin numbers.

Computer and software connection

Use the suitable D-SUB end with a computer's RS-232 port. A USB-only computer needs a converter providing a genuine RS-232 interface. For an integrated USB cable, also review UC-PRG020-12A.

With PLC-supported WPLSoft, or ISPSoft on suitable CPUs, match the COM number, speed and data format to the device settings. DVPACAB230 itself needs no USB driver; when a USB converter is used, its driver belongs to that converter.

Read the existing program and confirm device identity before downloading a new program. For connection faults, check port selection and cable continuity before changing PLC settings. Other options are covered under DVP interfaces.

Differences from other cables

DVPACAB215 is the catalogue's 1.5-metre option in this group. The earlier DVP manual distinguishes DVPACAB2A30 as the model without a DB25 connection. Keep these codes separate when ordering.

UC-MS030-01A is a 3-metre mini-DIN/female DB9 cable, and UC-MS020-01A is 2 metres. UC-MS010-02A offers 1 metre and a 90-degree mini-DIN connector. Compare pin assignments and required connectors before replacing an older cable.

UC-MS030-06A and UC-MS020-06A appear with male DB9 connectors in the selection guide. UC-PRG030-10A uses another DB9 arrangement. Similar names or matching lengths do not establish direct interchangeability.

Editor's Note

Establish what the cable actually is. Older installations may contain replacement connectors or labels transferred to another cable. Request photographs of both ends and any DB25 branch before relying on the model name.

Check the purpose of a DB25 computer port. A 25-pin connector on an older computer may be a parallel printer port. DVPACAB230 requires RS-232; verify the port label and computer documentation.

Disconnect both devices before continuity measurements. Check TX, RX and GND against the applicable DB9 or DB25 assignments, followed by the bridge groups. Keep the two connector numbering schemes separate.

Do not connect the DB9 and DB25 branches to two computers simultaneously. Treat them as alternative ends for the appropriate serial port. Begin testing with one computer and a known working PLC.

Investigate intermittent faults near the connector entries. Gently flex the cable during measurement or communication checks. Look for broken conductors, loose solder joints and poor contact, and ensure that any repaired connector provides proper cable strain relief.

Check the converter separately after a computer change. The driver or COM number may have changed. Changing the cable and PLC settings together obscures the cause; make one change at a time.

PDF diagrams and software

Use our Delta PLC accessories PDF and software files page for documentation. Consult Appendix A, Communication Wiring Diagram in the earlier DVP Series User Manual and Figures 12, 15 and 16 in the TP04G-AL/AL2 document.

Related subjects

For other options, see DVP communication cables, DVP programming cables, Delta PLC accessories and used Delta PLC models.

Navigation: Used Delta products | Delta PLC models | PLC accessories | Communication cables | PDF and software files

External references

Delta DVP/TP catalogue, accessories | Delta DVP Series User Manual, archive copy | Delta TP04G-AL/AL2 wiring diagrams | Delta TP02G-AS1 legacy cable drawings