6ES5 464-8MG11
Siemens 6ES5 464-8MG11 — 4–20 mA Analog Input for S5-95F
6ES5 464-8MG11 is an analog module with four 4–20 mA inputs, intended for failsafe analog processing in S5-95F applications, within the Siemens SIMATIC S5 family. This analog input module supports 1, 2 or 4 active channels in the S5-95F control system. The safety function depends on redundant module wiring and the appropriate program evaluation.
It converts the analog signal from a pressure transmitter or differential pressure sensor into digital data. Four physical inputs do not mean that one module alone provides four independent safety functions. Measurement pairs or groups of three must follow the project’s safety circuit.
Input range and wiring
The input range is 4–20 mA, with an input resistance of 31.25 Ω. Distinguish voltage and current signals; do not apply a voltage signal directly to the analog input. Two-wire or four-wire transmitters connect through the current loop while retaining their required supply arrangement.
Input terminals are Ch0: 3 (+)/4 (−), Ch1: 5 (+)/6 (−), Ch2: 7 (+)/8 (−), Ch3: 9 (+)/10 (−). Terminals 1 and 2 are not transmitter supply outputs. The complete wiring diagram is on page A-9 of the Siemens S5-95F manual.
Supply and galvanic isolation
The module typically draws 70 mA from the 9 V bus and does not supply transmitter power. Review the S5 bus supply and the transmitters’ 24 V DC supply separately. Siemens requires the sensors to use the same 24 V DC source as the base unit.
The inputs are galvanically isolated from ground, but not from each other. The maximum permitted potential difference between inputs is ±1 V. Check grounding and cable connections against the common references of the connected field devices.
Failsafe operation and FB 232 / FB 233
Safety-related operation requires at least two 464-8MG11 modules, distributed between S5-95F subunits A and B. FB 232 checks two analog values for discrepancy; FB 233 checks three. Standard analog reading alone does not provide the required safety-related PLC program evaluation.
Associated signals must be read from different modules. Verify input module addresses, sensor redundancy, permissible deviation, fault response and substitute values against the selected circuit. Non-failsafe sensors must also meet Siemens’ diversity and redundancy requirements.
Channel selection and digital data
Analog-to-digital conversion produces a 12-bit plus sign, left-justified two’s-complement value. The 1/2/4-channel setting must match the program. Check scaling against the raw input word, FB 232/FB 233 parameters and the required engineering units.
The manufacturer specifies a basic error of ±0.2% at 25°C and an operational limit of ±0.45% over 0–60°C. These describe the module’s measurement performance; they do not establish the performance of the complete safety chain.
Diagnostics and functional testing
The module has no integral functional-test facility. Testing at the user level must follow the selected I/O circuit and the intervals listed in the manual. The technical table also specifies no separate sensor-line wirebreak or group wirebreak indication.
During PLC troubleshooting, evaluate the raw measurements, the DISK discrepancy flag and the transition to the safe state together. For static process signals, verify the required test sequence and sensor supply monitoring in the existing safety program.
Editor’s note
464-8ME11 also measures 4–20 mA; that shared range does not establish interchangeability for a safety function. 464-8MD11 is the ±20 mA version and 464-8MC11 the ±10 V version. Confirm the complete 8MG11 suffix when ordering.
When reviewing the S5 installation, record the A/B subunit, module slot and field sensor associated with each input. A photograph of the front connector alone may be insufficient to reconstruct a cross-connected safety circuit.
Using the approved test arrangement, check every active channel separately at 4, 12 and 20 mA. Confirm the 4–20 mA sensor’s supply requirements. Follow the plant’s testing and shutdown procedure before disconnecting a safety loop.
If two pressure sensors disagree, first examine the sensors, supplies, wiring and scaling. Do not increase ABS/REL limits or the delay arbitrarily to silence a discrepancy alarm.
When buying used, request the label, channel measurement results and known repair history. Correct readings in an analog measurement application alone do not establish acceptance for the plant’s safety function. Complete the required functional verification after replacement.
OtomasyonAVM resources and PDFs
+ About Siemens S5 PLC — system and maintenance information.
+ S5 analog modules — ranges and model options.
+ Siemens S5 PDF archive — manual and download pages.
Related topics
+ 6ES5 095-8FB01 — S5-95F base unit.
+ 6ES5 464-8ME11 — standard 4–20 mA analog input.
+ 6ES5 464-8MD11 — ±20 mA analog input.
Browse SIMATIC S5
+ Siemens second-hand equipment
Siemens and external references
+ Siemens S5-95F Manual, English — §5.5.3; redundant modules and sensor supply requirements.
+ Same manual — §11.7–11.8; FB 232/FB 233, safety circuits and functional testing.
+ Same manual — A-9–A-10; wiring and specifications for the exact 6ES5 464-8MG11.