Delta DVPACAB7B10
Delta DVPACAB7B10 1-Metre IDC 40P–20P×2 I/O Cable
Delta DVPACAB7B10 is a 1-metre external terminal connection cable with one 40-pin IDC connector branching into two separate 20-pin IDC connectors. It carries signals from a compatible output module to terminal groups. It belongs to Delta DVP / AH I/O cables and Delta PLC accessories.
DVP32SN11TN and relay terminal connection
The manufacturer's DVPAETB instruction sheet specifies DVPACAB7B10 for connecting DVP32SN11TN to DVPAETB-OR16A. The two 20-pin branches separate the control connections to two 16-output relay terminals. The relays are on the external terminals; the cable itself contains neither output drivers nor relays.
Check the complete output-module code as well as the CPU selected under Delta DVP PLC series. Connect loads through the terminal's relay contacts. Do not treat relay-contact load ratings as permissible ratings for the IDC cable's signal connections.
Terminal selection in AH systems
The legacy AH500 hardware manual shows DVPACAB7B10 with DVPAETB-OR16A for AH64AN02T-5C, and with DVPAETB-OR16B for AH64AN02P-5C. When selecting Delta AH external terminals, verify the A/B suffix, module output design and common-terminal arrangement together.
Distinguish the module's total output count from the group carried by a single 40-pin port. Determine cable and terminal quantities from each port's wiring diagram; two branches on one cable do not establish that the complete module has been connected.
CN1, CN2 and CN3 orientation
The AH500 drawing identifies CN1 as 40-pin and CN2 and CN3 as 20-pin connectors. Check orientation and pin 1 markings at the module end and both terminal branches. Contact-face and cable-side views must not be read as the same orientation.
Label both branches by output group or connected terminal. Record the existing cable placement, PLC output addresses and terminal Y/C markings. Swapping branches can cause field outputs to operate different loads from those intended.
Differences from other cables
DVPACAB7A10 has a different arrangement connecting 40-pin IDC ends directly. Check connector and device matching separately for DVPACAB7C10, DVPACAB7D10 and DVPACAB7E10 in the same accessory family.
Consult UC-ET010-24C and UC-ET010-24D when examining other 40P–20P×2 cable options. Compare pin assignments, terminal compatibility and shielding when changing models. Matching pin counts alone do not establish a direct replacement.
Installation and software
1 metre is the physical cable length. Allow for both branch routes, cable-duct bends and maintenance access when positioning the terminals. Engage the latches fully, keep the ribbon cable clear of sharp edges and avoid pulling on the connectors.
No program or firmware is loaded into the cable. Select Delta WPLSoft or Delta ISPSoft according to the connected CPU and system generation. When replacing the cable, preserve and verify existing output addresses and their assigned loads in the program.
Editor's Note
The cable branches from one long connector into two shorter connectors. Still, check the DVPACAB7B10 label, module code and complete relay-terminal designation together rather than selecting by appearance alone.
Label both branches before removal and record which output group each terminal carries. Do not swap similar-looking plugs and then compensate by changing the program.
Inspect a used cable's IDC connector seating, latches and ribbon entries. Disconnect power and remove both ends before measurement, then gently move the cable entries to check for intermittent breaks.
If every relay in one terminal group fails to operate, check terminal power and common connections as well as the cable. For a single-channel fault, assess the relay, contact, field load and relevant conductor separately.
Prevent machine movement safely during initial testing. Check outputs individually and verify that the correct terminal and load operate. A clicking relay alone does not prove that its load contact is sound.
PDF and wiring documentation
Consult Delta PLC accessories files and Delta PLC and HMI manuals for relevant documents. The DVPAETB-ID32A/OR16A Instruction Sheet covers the DVP connection. The legacy AH500 Hardware Manual documents DVPACAB7B10's CN1/CN2/CN3 arrangement and AH terminal matching, with relevant drawings on printed pages 3-21 and 3-25.
Related topics
Delta DVP32SN11TN · Delta UB-10-OR16A / DVPAETB-OR16A · Delta UB-10-OR16B / DVPAETB-OR16B · Delta DVPACAB7A10 · Delta UC-ET010-24C · Delta AH external terminals
Return to Delta PLC accessories. Browse controllers in the Delta PLC category and available equipment under second-hand Delta products.
External references: Delta DVPAETB Instruction Sheet (archived manufacturer document) · Delta AH500 Hardware Manual (archived manufacturer document)