Delta AH32AM10N-5B
Delta AH32AM10N-5B – 32-Channel 24 V DC Digital Input Module
The Delta AH32AM10N-5B is a 32-channel digital input module for Delta AH500 PLC systems. Its inputs are rated at 24 V DC, 5 mA and accept NPN or PNP signals with the corresponding common wiring. Among Delta AH digital modules, this variant is identified by its 37-pin DB37 connector.
The module collects signals from sensors, limit switches and dry contacts in panels with a high input count. Dry-contact wiring uses a 24 V DC input circuit. The front-panel LEDs show the status of the optocoupled input channels.
Input Thresholds and Response Time
Delta specifies an ON threshold above 15 V DC and an OFF threshold below 5 V DC. Input impedance is 4.7 kΩ. Nominal response time is 10 ms from OFF to ON and 15 ms from ON to OFF, with a specified maximum input frequency of 50 Hz. When reading short pulses, check the duration of both the ON and OFF portions.
DB37, S/S Commons and Panel Wiring
Delta’s wiring example connects the module to the UB-10-ID32B / DVPAETB-ID32B external input terminal using the UC-ET010-33B 1-metre DB37 cable. Field wiring terminates at the external block. Compare the exact part numbers in AH I/O cables and AH external terminals.
Wire the S/S commons according to the sensor output type and the manufacturer’s diagram. In the standard arrangement, connect S/S to +24 V for an NPN output and to 0 V for a PNP output. When using multiple commons, check which input group each terminal serves.
ISPSoft and X Addressing
Add the module to the correct rack and slot in HWCONFIG within ISPSoft. It occupies 32 bits of X input space. For example, if the start address is X0.0, the two 16-channel groups are X0.0–X0.15 and X1.0–X1.15. Check the actual start address in the project. When expanding a rack, review the layout of the AH expansion modules and the capacity of the AH power supply.
5A, 5B and 5C Variants
The AH32AM10N-5A uses a removable terminal block, the AH32AM10N-5B uses DB37, and the AH32AM10N-5C uses a latching MIL connector. All three have 32 inputs. Check the complete suffix and the existing panel cable when choosing a replacement.
Manuals and PDF Downloads
Delta AH500 Hardware Manual – AH32AM10N-5B wiring diagram · English, April 12, 2023. Opens at section 4.7.12, printed page 4-43. Input specifications are on page 2-29 and HWCONFIG addressing is on page 5-13.
Delta PLC/HMI Cable Selection Guide – DB37 cable and terminal pairing · English, section 2.2.1, printed page 2-3.
Editor’s Note
When buying used, read the full AH32AM10N-5B code on the label. The front-panel 32AM10N marking is shared across the three connector variants.
Inspect the DB37 socket under good light. If you see bent pins, loose screw fittings or movement at the cable entry, test the cable as well.
If the module comes with a cable and terminal block, check for the UC-ET010-33B and UB-10-ID32B markings first.
On the bench, test one input from each 16-channel group. Watch the LED first, then check the corresponding X bit in ISPSoft.
If a whole group fails to register, start by checking the 24 V supply, the group’s S/S common and continuity through the DB37 cable.
Related Topics
See the AH16AM10N-5A for fewer inputs or the AH64AM10N-5C for higher input density. For DB37-connected outputs in the same system, the AH32AN02T-5B provides NPN outputs and the AH32AN02P-5B provides PNP outputs. Use the terminal block specified for the exact output module.
Delta Navigation
Delta AH PLC series · Delta PLC accessories · Delta PLC series · Delta PLC and HMI manuals · Second-hand Delta Automation
External References
Delta AH Series Catalogue · Delta PLC/HMI Cable Selection Guide (DigiKey copy)