Delta AH I/O cables
Delta AH I/O cables
Delta AH I/O cables carry signals between suitable digital I/O, counter or motion-control hardware and an external terminal module in a Delta AH500 system. Select using the cable code, complete module suffix and terminal model together. MIL/IDC, DB37, MDR36 and MDR50 connections differ; a cable alone does not establish additional I/O capacity or communication protocol support.
A and B cables with MIL/IDC connections
Delta DVPACAB7A10 is paired with UC-ET010-24A in AH Motion documentation: a 1-metre IDC 40-to-IDC 40 cable. It is illustrated for AH32AM10N-5C and AH64AM10N-5C input modules; other -5C connection examples depend on the selected terminal.
Delta DVPACAB7B10 is paired with UC-ET010-24C: a 1-metre IDC 40-to-two IDC 20 cable. It serves the relevant terminal arrangements for AH32AN02T-5C, AH32AN02P-5C, AH64AN02T-5C and AH64AN02P-5C output modules. The 40-to-40 and 40-to-20×2 arrangements must be distinguished.
C cable and UC-ET010-33B with DB37 connections
Delta DVPACAB7C10 and its listed counterpart Delta UC-ET010-33B form the 1-metre male DB37-to-male DB37 connection group. Manufacturer tables show AH32AM10N-5B, AH32AN02T-5B and AH32AN02P-5B.
The documented pairings include UB-10-ID32B / DVPAETB-ID32B for AH32AM10N-5B, UB-10-OR32A / DVPAETB-OR32A for AH32AN02T-5B and UB-10-OR32B / DVPAETB-OR32B for AH32AN02P-5B. UB-10-OT32B / DVPAETB-OT32B is another terminal option shown for both output models. Verify relay/transistor terminal selection and field power separately.
36-pin and 50-pin motion-control connections
Delta DVPACAB7D10 is paired with Delta UC-ET010-13B, a 1-metre female MDR36-to-female MDR36 cable. The guide shows AH04HC-5A and AH20MC-5A connections to UB-10-IO16C / DVPAETB-IO16C. This pairing must not be extended to every motion-control port with a similar appearance.
Delta DVPACAB7E10 is paired with Delta UC-ET010-15B, a 1-metre female MDR50-to-female MDR50 cable. AH10PM-5A connects to UB-10-IO24C / DVPAETB-IO24C, while AH15PM-5A connects to UB-10-IO34C / DVPAETB-IO34C. The 36-pin and 50-pin cables serve different hardware connections.
Selection and connection checks
Check the module's -5B / -5C suffix, connector gender, pin count, input/output direction and common power terminals. These cables have no programming software of their own; CPU and module configuration is a separate task. External terminal wiring serves a different purpose from backplane extension or Ethernet communication.
Start document selection at Delta PLC accessories files. Sections 2.4 Cable Models and 2.5 Descriptions of Cable Models in the Delta PLC/HMI Cable Selection Guide provide module–cable–terminal combinations and drawings. Verify the connection against the hardware manual for the exact module.
Editor's Note
Do not decide from the cable label alone. Inspect the complete module code, both connectors and the terminal label together. Checking -5B versus -5C helps eliminate an unsuitable cable before ordering.
Check continuity with both ends disconnected from equipment. Compare conductors and unintended shorts against the manufacturer's drawing. Do not apply a high-voltage insulation test while an electronic module or terminal remains connected.
A failed channel does not immediately condemn the entire cable. Connector pins, terminal screws, common connections and any terminal relay share the signal path. An interruption that changes when the cable moves may indicate a conductor or contact fault near the connector.
Do not bridge common terminals by guesswork. Verify supply polarity, NPN/PNP circuits and terminal type against the drawing. A connector fitting the housing does not guarantee the same electrical connections.
Evaluate used cables on a suitable test setup. Check channels individually and inspect loose latches, missing DB screws, crushed insulation and bent pins. Leave strain relief at installation and route the cable separately from drive motor wiring.
Related topics
Review terminal choices under Delta AH external terminals and other supporting hardware under Delta PLC accessories. Use Delta PLC and HMI manuals for model documentation.
External references: Delta PLC/HMI Cable Selection Guide — 2019, English · Delta AH Motion Hardware Manual — 2016, English.