Delta UC-PRG030-10A

Delta UC-PRG030-10A — 3 m RS-232 Programming Cable

Delta UC-PRG030-10A is a 3 m RS-232 programming and serial communication cable with female DB9 connectors at both ends. It connects a suitable PLC, HMI or TP device to a computer serial port. This model in the Delta DVP programming cable range has crossed transmit and receive lines.

The cable provides a passive serial connection. It contains no USB converter, RS-485 interface or programming software. Confirm the target device’s RS-232 pin assignment, connector gender and project transfer method; a DB9 socket alone does not establish compatibility.

Pin connections and crossover wiring

Manufacturer Figure 12 shows 3 → 2, 2 → 3 and 5 → 5. A straight-through DB9 extension is therefore not an equivalent connection. Follow pin numbers and distinguish the connector mating face from its solder-side view.

First female DB9 Second female DB9 Connection
3 2 Tx → Rx
2 3 Rx ← Tx
5 5 GND ↔ GND

The diagram shows Tx, Rx and GND. Do not assume that hardware handshake lines such as RTS/CTS are connected. Match flow control and serial settings to the target device’s requirements. This three-wire arrangement performs no voltage-level or protocol conversion.

Device compatibility and adapters

Delta’s guide illustrates PC connections for TP02G-AS1 and TP04G-AS2 in the TP panel range. The TP04G-BL-C instruction sheet also specifies UC-PRG030-10A for a PC connection through COM1 RS-232. Check the complete panel code because TP models can have different port arrangements.

For DVP PLC applications, follow the wiring diagram for the interface card, such as DVP-F232. The cable guide shows an additional male-to-male null modem adapter for its F232S connection. Check adapter requirements when selecting DVP interfaces or AH PLC connections. A gender changer and a crossover adapter are different components.

Computers without an RS-232 port

A USB-only computer requires a suitable USB-to-RS-232 converter. Its driver and virtual COM port belong to the converter; UC-PRG030-10A has no USB driver of its own. Match the COM number, baud rate, data bits, parity and stop bits to the target device in the communication software.

UC-PRG020-12A is a separate USB serial connection option. UC-PRG030-01A uses mini USB, UC-PRG030-02A uses USB Type-B and UC-PRG030-20A has RJ45 connectors. UC-PRG015-01A and UC-PRG015-02A also have different port arrangements. Preserve the complete ordering suffix.

Differences from mini-DIN cables

UC-MS010-02A, UC-MS020-01A and UC-MS030-01A serve applications with an 8-pin mini-DIN connection. UC-MS030-06A has a different HMI/PLC connection arrangement. When comparing DVP communication cables, check the target port and connection direction together.

Editor’s Note

Female DB9 connectors at both ends do not identify the wiring. Disconnect the cable from both devices and check continuity for 2–3, 3–2 and 5–5 first. This quickly distinguishes a crossover cable from a straight extension.

During continuity testing, gently flex the cable near each connector entry. A damaged conductor can pass while stationary and open when bent. Also check for unintended shorts between neighbouring pins.

Account for every adapter in the connection. Two separate crossover stages can produce a straight-through result overall; record each component’s pin mapping before blaming the device.

With a USB converter, establish the actual COM number first. Healthy hardware cannot communicate if the software uses another port. Close other applications that may have the same port open.

A loopback test with the target disconnected can help check the computer serial interface, but it does not validate the panel port. Isolate the computer, converter, cable and target interface in sequence.

Back up the existing project and communication settings before transfer whenever possible. Resetting a working device because a connection fails can turn a simple wiring fault into a much larger job.

PDF, software and related topics

Use the Delta PLC accessories PDF and software files page for pin diagrams and related software links. Panel documents are also available under Delta TP panel files.

Use TPEditor for applicable TP projects and consider WPLSoft or ISPSoft for supported PLC models. Select software for the target device. Further connection information is available under Delta HMI programming and HMC cables and Delta PLC and HMI manuals.

Navigation: UC-PRG030-10A main page · Delta PLC accessories · Delta PLC models · Used Delta products

External references

Delta PLC/HMI Cable Selection Guide — Figure 12, 1-85 / 1-86 · Delta TP04G-BL-C Instruction Sheet — PC connection · Delta DVP / TP Catalogue — Programming and Serial Communication Cables