Delta UC-PRG030-02A
Delta UC-PRG030-02A
Delta UC-PRG030-02A is a 3-metre data connection cable with a male USB Type-A connector at the computer end and a male USB Type-B connector at the device end. Manufacturer documentation illustrates it for connecting suitable TP and DOP panels to a computer. Verify the complete panel model and physical USB port before ordering.
USB Type-B connection and supported devices
The manufacturer catalogue lists TP70P / TP04P / DOP families for UC-PRG030-02A. Review the connection drawings for Delta TP70P and Delta TP04P. For DOP panels, family names such as Delta DOP-B or Delta DOP-100 alone are insufficient: verify the USB device/PC connection port on the exact model.
The USB Type-A plug connects to the computer, while the conventional four-pin USB Type-B plug connects to the appropriate panel's PC interface. Distinguish this from a panel's USB host port intended for USB storage. Use Delta HMI Files and Delta HMI Programming and HMC Cables for supporting model and connection information.
The manufacturer's Figure 19 identifies 1: +5 V, 2: D−, 3: D+, 4: GND at both ends. Interpret pin numbers using the connector viewing direction shown in the drawing. USB connection does not remove the panel's external power requirements specified in its own manual.
Differences from similar cable codes
Delta UC-PRG015-02A is the 1.5-metre USB Type-A-to-Type-B option. Delta UC-PRG030-01A is listed for a 3-metre mini-USB connection and has a different device connector. Do not interchange the 01A and 02A suffixes.
Delta UC-PRG020-12A serves USB-to-RS-232 connections, Delta UC-PRG030-10A serves DB9 serial arrangements and Delta UC-PRG030-20A serves RJ45 network connections. UC-PRG030-02A is not a USB-to-RS-232 converter. Select from Delta DVP programming cables according to the actual port standard.
Software, USB drivers and project transfer
The cable has no programming tool of its own. For a suitable TP panel, consider the interface project in Delta TPEditor separately from the supported Delta WPLSoft project for built-in PLC functions. Check CPU and software scope together under Delta PLC software.
Select the USB device driver for the connected panel and computer operating system. The TPEditor manual's USB-driver appendix describes the installation directory's USB folder for supported TP panels. Do not assume that every device must create a virtual COM port. Device recognition and transferring a project to the correct device type require separate checks.
Start document selection at Delta PLC accessories files. In the Delta PLC/HMI Cable Selection Guide, Figure 19 on printed page 1-88 gives connector and pin drawings; pages 1-71 and 1-76 illustrate TP/DOP connections. Review other panel connection options under Delta HMI Communication Auxiliary Units.
Editor's Note
Inspect the panel socket first. Distinguish Type-B, mini-USB and USB host ports. Cables starting with UC-PRG030 do not all have the same connector; read the complete suffix.
If the computer does not recognise the panel, check the connection systematically. Check panel power and USB device status, then compare with a suitable known-good cable and another computer port. Select any required device driver from the correct panel software.
If movement causes disconnections, inspect both sockets. A connection dropping when the cable moves may indicate a broken conductor near the plug or a contact fault in the panel socket. Look for bent contacts and a loose Type-B housing.
Back up the working project first. Save the panel interface and built-in PLC program separately, and check device type and project version before transferring. Replacing a cable does not resolve an incorrect project or password restriction.
Avoid adding unnecessary extensions to the three-metre cable. During troubleshooting, remove hubs and additional cables to compare a direct connection. Evaluate a used cable through actual data transfer with a suitable panel as well as continuity checks.
Related topics
Review other supporting hardware under Delta PLC accessories and device documentation under Delta PLC and HMI manuals.
External references: Delta PLC/HMI Cable Selection Guide — 2019, English · Delta DVP/TP Catalogue — 2024, English · Delta TPEditor Manual — USB-driver appendix, English.