Delta IFD6503
Delta IFD6503 USB / CAN Communication Interface
Delta IFD6503 is a portable communication interface used to monitor CAN messages and transmit messages through a computer's USB connection. It is used when examining CANopen and DeviceNet networks. Within the Delta DVP interface range, it provides computer access to the CAN network during maintenance and commissioning.
The manufacturer describes receiving, filtering and displaying standard and extended CAN frames according to the protocol. Software functions include one message sent manually and up to eight messages in automatic mode. These capabilities do not establish support for every programming operation on a particular PLC or drive.
Technical specifications and power supply
IFD6503 is powered by the connected computer's USB port; the module requires no external power supply. Stated consumption is 0.6 W. The computer connection is USB Type A, with an 8-pin RJ-45 connector for CAN.
Supported CAN rates are 10, 20, 50, 100, 125, 250, 500 and 800 kbit/s, plus 1 Mbit/s. Match the rate to the existing network. Assess cable length and topology before choosing the highest setting.
Document matching note: Delta's product page lists 500 VDC isolation, while the 2018 IFD6503 instruction sheet lists 1,000 VDC. Use documentation matching the unit's hardware revision for this rating.
RJ-45 CAN connection
Manufacturer pin assignments: 1 CAN_H, 2 CAN_L, 3 CAN_GND, 6 CAN_SHLD, 7 CAN_GND. Pins 4, 5 and 8 are reserved. Check connector orientation against the manual drawing. This RJ-45 port carries CAN communication and is not an Ethernet connection.
For network wiring, review Delta CANopen cables, UC-DN01Z-01A for the main line and UC-DN01Z-02A for branches. Select cables and connection accessories according to the physical network arrangement.
Distribution points may use accessories such as TAP-CN01, TAP-CN02 and the RJ-45-based TAP-CN03. Record the existing termination arrangement and avoid changing the number of terminators when connecting the computer interface.
Driver and NetView Builder
The IFD6503 hardware driver and NetView Builder are separate components. The driver allows the computer to recognize the interface; analysis software works with CAN traffic. Check operating system and 32/64-bit compatibility before installation.
When reviewing a NetView Builder capture, examine the CAN identifier, data length, data bytes and timing together. Verify that filters display the intended messages; an empty display does not automatically establish a network fault.
The CANopen Builder and DeviceNet Builder pages cover network configuration software separately. Distinguish their tasks from those of the message analysis software used with IFD6503.
LED indicators and initial diagnosis
Steady green USB LED: successful USB connection; flashing indicates data exchange. CAN LED off: initialization complete. Flashing yellow CAN LED: CAN traffic. Steady yellow can occur during initialization or BUS-OFF/error conditions and does not alone prove hardware failure.
First confirm computer recognition, selection of the correct interface in software and the matching CAN rate. Check USB connection and field CAN communication separately.
Separate roles of other Delta modules
IFD6500 and IFD6530 belong to the USB/RS-485 group; IFD6503 provides USB/CAN access. IFD8500-A is considered for serial interface conversion. Identify the communication type before selecting a model.
The IFD9503 CANopen and IFD9502 DeviceNet gateways have different tasks. In applications with Delta DVP PLC network modules such as DVPCOPM-SL and DVPDNET-SL, IFD6503 helps the maintenance computer examine the bus.
Editor's Note
Capture the existing traffic first. Establish the network rate and normal message pattern on a working machine. Keep a known reference capture before starting any message transmission.
USB power does not mean the entire network is powered. Check field node supplies and network power separately. Recognition of the adapter by the computer does not prove that other devices have power.
Ask for testing with real CAN traffic when buying used. Computer recognition alone is insufficient. Check reception on a known network, transmission in a controlled test setup and a stable USB connection.
Measure resistance with power disconnected. A conventional CAN segment with 120-ohm termination at each end should measure approximately 60 ohms between CAN_H and CAN_L. Investigate different readings for broken wiring or missing/excess termination; this measurement alone does not certify the network.
A visible message still needs correct interpretation. Compare its identifier and data bytes with the device's protocol documentation. Record filter and display changes so that a later investigation can reproduce the same view.
Support the small adapter against cable strain. Avoid loading the USB plug or RJ-45 latch. For intermittent disconnections, inspect ports, plugs and cables before investigating components on the circuit board.
PDF manuals and software
Use our Delta PLC accessories PDF and software files page for documentation. Match the pin table, driver installation and LED descriptions in the IFD6503 Instruction Sheet to your equipment.
Related subjects
For other equipment, see Delta PLC accessories, DVP interfaces, CANopen cables and used Delta PLC models.
Navigation: Used Delta products | Delta PLC models | PLC accessories | DVP interfaces | PDF and software files
External references
Delta IFD6503 product page | Delta IFD6503 Instruction Sheet, 2018-10-22 | Delta AS Operation Manual, CANopen chapter | maxon: CAN termination and resistance checks