Delta ASDA-B3
Delta ASDA-B3 Servo Drive Series
The Delta ASDA-B3 is a family of AC servo drives that use motor feedback to follow commands from a PLC or motion controller. Typical applications include position control on feeding and packaging axes, and speed and torque control in winding and tension applications. Delta specifies a speed-loop bandwidth of up to 3.1 kHz. Start with the full part number, supply class and machine command interface.
B3 and B3A model codes
The -L variant provides pulse commands and RS-485. The -M uses CANopen, the -F uses DMCNET, and the -E uses EtherCAT. The B3A-P is the PROFINET variant. For example, ASD-B3A-0421-E identifies a 400 W, 220 V-class EtherCAT drive. Check the nameplate and the model’s specification table for the allowed supply voltage and phase configuration.
The 2025 manual lists pulse inputs for the B3-L, B3A-L, B3A-M, B3A-F and B3A-E. CN1 has 44 pins on L models and 26 pins on M/F/E and B3A-P models. For pulse commands, check the electronic gearing ratio against the machine’s units. For analog speed or torque commands, verify the analog input and scaling for the exact drive model.
Motor, encoder and cable matching
Delta’s 2025 manual lists ECM-B3 motors and selected 220 V ECM-A3 combinations. For motor selection, consider rated torque, speed and load inertia alongside power. Find the exact motor in the drive matching table, then check the absolute encoder, feedback and holding brake options. A 24-bit absolute encoder is available on compatible motors.
The Delta servo motor section includes ECM-A3L and ECM-A3H. When choosing a Delta servo cable or encoder connector, verify both the drive and motor ends. Correct grounding and cable routing help reduce signal interference at the CN2 encoder connection.
Commissioning, braking and STO
Use ASDA-Soft through the CN4 Mini USB connection for parameter setup, monitoring and backup. On the first motion test, confirm the motor direction, home reference and limit switches. Then check auto-tuning and servo loop gain under the machine’s load. For EtherCAT controller-to-drive communication, check that the ESI file and project mapping match the drive.
Regenerative energy during deceleration matters on high-inertia axes and in frequent-stop applications. Select the braking resistor resistance and power rating from the drive model’s table. For STO on B3A models, use the safety diagram for the exact drive. See Delta servo STO connections and Delta servo braking resistors for related connections and parts.
ASDA-B3 user manual and catalogue
Delta ASDA-B3 User Manual (PDF, English) — PDF pages 30–31 show the drive variants, and pages 36–38 list motor matches. Chapter 3 covers wiring, Chapter 5 covers tuning, and Chapter 14 covers alarms.
Delta ASDA-B3 Series Catalogue (PDF, English) — Model codes, motor options and accessory tables. Both documents are also listed in the Delta Servo Manuals section.
Editor’s Note
Buying used. Ask for photos of the full drive label, supply markings and CN1/CN2 sockets. If the machine uses an -E drive, verify the full -E part number on the spare.
Drive replacement. When replacing an ASDA-B2, record the existing motor code and both cable ends. Check the combination against the B3/B2 conversion cable table in Appendix B.11.
Backup. While the old drive is accessible, save its ASDA-Soft parameter file and record the PLC command type, gear ratio and homing direction. Check these first on the replacement drive.
AL004 and AL011. For AL004, start with the motor-to-drive matching table. For AL011, inspect the CN2 encoder connection. Check connector seating and cable damage after power has been safely isolated.
AL002 during deceleration. Record when the alarm occurs. Review deceleration time, load inertia and braking resistor selection together.
Bench test. Secure the compatible motor and compare commanded and actual direction at low speed. Before coupling it to the machine, confirm stable feedback and check operation of the holding brake where fitted.
Related Delta equipment
Delta ASDA-A3 · Delta AS PLC series · Delta AH motion controllers · Delta motion control cards
More in this range · Delta Servo Drives · Delta Servo Modules and Accessories
External references
Delta ASDA-B3 2025 User Manual (distributor archive) · Delta ASDA-B3 2024 Catalogue (distributor archive)