6ES5 467-8EE11

Siemens 6ES5 467-8EE11 — 4–20 mA Ex Analog Input Module

6ES5 467-8EE11 is an Ex analog input module for 4–20 mA signals, selectable for one or two channels, in the Siemens SIMATIC S5 family. It supports S5-95U/S5-100U and ET 100U/ET 200U systems. This S5 analog module converts transmitter current into digital values within the S5 modular I/O system.

It can read a suitable pressure transmitter or differential pressure sensor through an approved Ex circuit. The analog signal wiring depends on whether the transmitter is a passive two-wire device powered by the module or an independently powered four-wire device.

Ex protection and installation

The Siemens manual identifies the protection marking as [EEx ib] IIC. Install the module outside the hazardous area; its field measurement circuits are intrinsically safe. The channels are galvanically isolated from the S5 bus, but not from each other.

Use the 6ES5 700-8EA11 Ex bus unit and a 6ES5 497-8EA11 partition between Ex and standard circuits. Review grounding and cable installation together with the transmitter certificate and the plant’s intrinsic-safety assessment.

Two-wire and four-wire connections

Two-wire connection: channel 0 uses 3 (+), 4 (−); channel 1 uses 7 (+), 8 (−). The module powers the transmitter. Confirm that the 4–20 mA sensor supports a passive loop; do not add a supply across the analog input.

Four-wire connection: channel 0 uses 4 (+), 6 (−); channel 1 uses 8 (+), 10 (−). The transmitter needs a separate intrinsically safe supply. Leave terminals 1 and 2 unconnected; do not short unused inputs. Matching the 4–20 mA signal range does not make these two wiring arrangements interchangeable.

Supply and channel selection

The module draws approximately 320 mA from the 9 V I/O bus. Assess the complete S5 supply load and check the arrangement of any PS 935 / 6ES5 935-8ME11 supplementary supply.

The front operating switch selects 50/60 Hz and single-channel Ch0 / two-channel Ch0–Ch1 operation. Match the analog-to-digital conversion setup to the channel configuration expected by the PLC. Single-channel operation starts with Ch0.

Scaling and programming

Siemens Table 11.8 gives 4 mA = 512 and 20 mA = 2560 measurement units. Linear interpolation gives the midpoint as 12 mA = 1536 units. In the PLC program, do not treat the input as a direct 0–2048 scale over 4–20 mA. Distinguish these units from the left-justified raw input word.

When using FB 250, check channel type 3 for 4–20 mA, the channel number and the engineering limits together. Verify the input module address against the installed CPU/ET system and the existing project.

Fault indication

Input current below approximately 2 mA or above 22 mA can trigger a fault indication. A flashing red LED indicates one faulty channel; a continuously lit LED indicates faults on both. During PLC troubleshooting, examine the LED, raw measurement and program fault handling together.

Editor’s note

Photograph the complete 467-8EE11 label, Ex marking and bus unit first. Include the field transmitter documentation when reviewing the S5 installation. A working module with an unreadable label or uncertain repair history does not establish suitability for an Ex circuit.

For bench testing, identify whether the calibrator sources current or simulates a two-wire transmitter. Select the cable and terminal connections accordingly. Do not connect an active source indiscriminately to the module’s transmitter supply terminals.

Check both channels separately at 4, 12 and 20 mA. In a pressure sensor application, record the engineering value displayed by the PLC as well. Correct raw readings with an incorrect pressure display call for a scaling check.

Pressure sensors with identical 4–20 mA outputs can have different supply requirements and Ex approvals. State the analog measurement application, cable length and transmitter’s minimum operating voltage before ordering.

6ES5 477-8EC11 is an Ex analog output module and cannot replace this input module for reading measurements. When buying used, request results for both channels, terminal photographs and matching documentation for the Ex circuit.

OtomasyonAVM resources and PDFs

+ About Siemens S5 PLC — system and maintenance information.

+ S5 analog modules — input and output models.

+ Siemens S5 PDF archive — available manual and download pages.

Related topics

+ 6ES5 700-8EA11 — bus unit for Ex modules.

+ 6ES5 935-8ME11 — PS 935 supplementary I/O supply.

+ 6ES5 477-8EC11 — 4–20 mA Ex analog output.

Browse SIMATIC S5

+ S5 analog modules

+ S5 modular I/O group

+ SIMATIC S5

+ Siemens second-hand equipment

Siemens and external references

+ Siemens SIMATIC S5 Ex I/O: S5-100U, English PDF — §11.8.1, two-/four-wire connections, operating settings and Table 11.8.

+ Same Siemens manual — 6ES5 467-8EE11 specifications and historical certificate data, F-11–F-13.