Delta Servo Communication Units
Delta Servo Communication Units
Delta servo communication units include cables, connectors and distribution boxes that connect a servo drive to a PC, PLC or motion controller. During commissioning, the PC connection lets you read and back up parameters. During machine operation, the selected network carries commands and status data between the controller and the drive. For multi-axis synchronisation, check the drive suffix, the controller’s supported protocol and the cycle settings together.
Communication cable and connector codes
ASD-CARS0003 — RS-232 PC communication cable, nominally 3 m. Used with the applicable CN3 interface on ASDA-A2 and ASDA-B2 drives. Check the drive plug and PC-side serial pin assignments in the relevant manual.
DOP-CAUSBAB — USB cable between the drive and PC, nominally 1.4 m. Delta lists this part in the ASDA-A2 and ASDA-A2R accessory tables. Use the applicable CN4 USB port for parameter reading and configuration in ASDA-Soft.
ASD-CNIE0B06 — RS-485 connector for a Modbus RS-485 connection on a compatible serial port. When wiring CN3, match the signal and pin assignments of the RS-232 or RS-485 interface to the exact drive manual.
TAP-CB03 and TAP-CB05 — CANopen cables measuring 30 cm and 50 cm respectively. TAP-CN03 is the CANopen distribution box. Delta’s A2 catalogue shows the box in the network connection between a CAN master and compatible servo drives.
Which protocol does CN6 carry?
ASDA-A2-M and A2-MN drives use CANopen on CN6. ASDA-A2-F and A2-FN drives use DMCNET. The ASDA-A2-E uses EtherCAT. On the A2-E, CN6A is the incoming port from the master side. CN6B continues to the next device in a line topology. Where ports look alike, use the full drive code and the signal names in the wiring diagram.
The difference between EtherCAT and conventional Ethernet matters when selecting controllers and network devices. For an EtherCAT servo axis, verify the device description, PDO mapping and real-time cycle settings in the master project.
Editor’s Note
Ask for photos of both cable ends before ordering. Keep the drive nameplate, port name, model at the other end and cable code in the same record. On a used TAP-CN03, inspect the ports and terminal blocks. Measure and label the 30 cm and 50 cm leads.
If ASDA-Soft cannot connect, check the connection path first. Select the interface that matches the CN4 USB or CN3 serial connection. For serial links, check which COM port the operating system detects and which interface the drive is set to use. Once connected, start by reading and backing up the parameters.
Start with one Modbus status register. Check the station address, baud rate, parity and stop bits. Both sides must use the same RTU or ASCII mode. Once a single drive responds, add the other stations one at a time. See the Modbus FAQ for addressing and data format.
Record CANopen termination and device addresses. When replacing a drive, check CAN_H/CAN_L assignments, bus-end termination, node address and bit rate. If faults begin under load, inspect cable routing, grounding and possible electromagnetic interference.
Check the EtherCAT link light and operational state separately. If Link/Activity is present and the axis fails to reach OP, inspect the master’s error code, ESI file, PDO mapping and cycle settings. During EtherCAT troubleshooting, record the first affected device and the order of devices on the line. After replacement, use a guarded low-speed test to verify direction, commanded travel and electronic gearing.
Delta servo communication PDFs
ASDA-A2 catalogue — RS-232, USB and CANopen accessories · English, 2023. Cable dimensions and the TAP-CN03 drawing. The ASD-CNIE0B06 RS-485 connector drawing is on the next page.
ASDA-A2 user manual · English, 2024. CN3 serial and CN4 USB · CN6 CANopen and the following DMCNET section.
ASDA-B2 — CN3 RS-232 / RS-485 wiring · English, 2023. CN3 terminal layout.
ASDA-A2-E — CN6 EtherCAT connection · English, 2022. CN6 connection and port functions.
Related Delta equipment
Motion control cards · Servo I/O connections · Servo cables · Operator panel cables
Delta Servo Modules and Accessories · Used Delta equipment · Delta Servo Manuals archive
External sources · A2 accessory catalogue · A2 manual · A2R catalogue · B2 manual · A2-E manual