Delta DVP08SN11TS

Delta DVP08SN11TS is a DVP-S digital expansion module that adds 8 PNP transistor outputs to a compatible DVP Slim PLC CPU. The Y0–Y7 terminals supply the positive side of each load when active. The module adds outputs only and occupies no X input addresses. The eight-point DVP08SN11T has NPN outputs, while DVP08SN11R has relay outputs.

Output ratings and UP/ZP wiring

The outputs are rated for 5–30 V DC. For resistive loads, Delta specifies 0.3 A per output and 2 A per common. Eight loads drawing 0.3 A each would total 2.4 A and exceed the common limit. Electronic response is approximately 15 µs ON and 25 µs OFF. Actual switching also depends on the PLC scan.

The CPU bus powers the module electronics. Feed the output stage from an external 24 V DC supply. Delta specifies a tolerance of −15%/+20%. Connect UP to +24 V and ZP to 0 V. Wire each load between its Y terminal and 0 V. The manual’s 15 mA maximum auxiliary consumption is additional to the field load current. The module weighs approximately 66 g, has removable terminals and fits a 35 mm DIN rail inside a control panel.

Output type and coil load selection

Trace the existing load return before replacing a unit. An active PNP output supplies positive voltage to the load. An active NPN output sinks current toward 0 V. Review PNP versus NPN and sink/source wiring together. Field sensors, such as an inductive sensor or a photoelectric sensor, connect to a separate input channel. Their output type does not change this module’s PNP output circuit.

Check the continuous current, any inrush and the number of DC valve or relay coils energised together. For a contactor coil or field load outside the output ratings, choose an interface relay with suitable coil and contact ratings. Follow the coil manufacturer’s suppression guidance. For example, check diode polarity and its effect on release time. Protect the external output branch with a suitable fuse and check the protective device’s DC voltage and current ratings.

Y addressing, software and programming cable

Y0–Y7 printed on the terminals are local labels. Addresses in the host PLC project depend on the CPU and expansion order. If the CPU occupies Y0–Y7 and this is the first digital output expansion, the example range is Y10–Y17. DVP addresses are octal. Verify the standard Y bits online before assigning HMI and SCADA tags.

Open the CPU project in WPLSoft or a CPU-compatible release of ISPSoft. Check COMMGR for ISPSoft. Connect the programming cable to the CPU. For a suitable 8-pin mini-DIN RS-232 communication port, Delta lists UC-PRG020-12A. On a PC without a serial port, verify the USB–RS-232 adapter driver and COM number. The CPU runs the automation logic.

Related modules

See DVP16SN11TS for more PNP outputs, DVP16SN11T for 16 NPN outputs or DVP06SN11R for six relay outputs. For combined inputs and PNP outputs, DVP08SP11TS provides 4+4 points and DVP16SP11TS provides 8+8.

DC input expansions include DVP08SM11N, DVP16SM11N and DVP32SM11N. DVP08SM10N has AC inputs and DVP08ST11N uses DIP switches.

Editor’s Note

Check the label for 08SN11TS. The difference between T and TS changes where the load return belongs.

If the Y LED is on but the load stays off, measure UP to ZP under load. Then inspect the Y connection and the load’s 0 V return.

If outputs work individually but fail when switched together, check the common current and the supply voltage drop.

After output damage, check the coil for shorts and inspect its suppression device. Test the replacement with a suitable 24 V load disconnected from the machine first.

For a used unit, request label and terminal photos. Ask for a measurement under load as well as the LED state on each of the eight outputs.

PDF manuals and technical documents

See the Delta DVP PLC files page and open section 7.4.10 of the DVP Series Module Manual. In the 6 January 2026 edition the UP/ZP diagram is on PDF page 138, printed page 7-14. Electrical ratings are on PDF pages 126–127.

DVP08SN11TS main page · Slim digital modules · DVP expansion modules · DVP PLC series · Delta PLC · Used Delta models · Delta manuals

External reference

Delta DVP Series Module Manual (2026)