Delta UC-CMC020-01A

Delta UC-CMC020-01A 2-Metre CANopen Cable

Delta UC-CMC020-01A is a 2-metre CANopen connection cable with RJ45 connectors at both ends. It belongs to Delta CANopen cables and Delta PLC accessories. The manufacturer's PLC/HMI cable guide also lists the UC-CMC family for DMCNET connections between supported devices.

Applications and port compatibility

The DVP catalogue associates this cable family with CANopen products including DVP10MC11T, DVP15MC11T, DVPCP02-H2 and DVPCOPM-SL. DVPCOPM-SL has a 5-pin removable CAN terminal, so an appropriate connector or distribution arrangement is required to complete the physical RJ45 connection.

The guide identifies the AH20MC-5A application as DMCNET. The cable does not convert between protocols. RJ45 appearance does not establish Ethernet operation or equivalence to Delta EtherCAT cables; follow the device's port label and wiring diagram.

CANopen and DMCNET pin distinctions

In Figure 1 on printed page 3-9, the guide identifies CANopen pins as 1: CAN+, 2: CAN-, 3 and 7: CAN_GND and 6: CAN_SHLD. Pins 4, 5 and 8 are unassigned in that table. Check connector orientation and the connected device's own pin table separately.

For DMCNET, pins 3 and 6 carry the second data pair. CANopen shield and ground assignments therefore must not be transferred unchanged to a DMCNET connection. Follow the manufacturer's drawings when fitting Delta network connectors or repairing cable ends.

2-metre connection and drop length

2 metres is the cable's physical length. Assess total network distance, baud rate, device count and drop layout separately. A short connection between nearby devices does not by itself establish that the complete network is suitable.

The TAP-CN03 instruction sheet gives a 6-metre maximum for DeviceNet/CANopen drop cables. UC-CMC020-01A is below that length limit, but the selected baud rate or devices may require shorter drops. Match the distribution box and cable to the project's protocol and pin assignments.

Check termination at both physical CANopen network ends, accounting for TAP-TR01 and existing device resistors. Installing a two-metre cable does not require adding a terminator at every connection point.

Other UC-CMC lengths and software

Shorter options include UC-CMC010-01A at 1 metre and UC-CMC015-01A at 1.5 metres. For longer routes, consider UC-CMC030-01A at 3 metres or UC-CMC050-01A at 5 metres. UC-CMC200-01A is 20 metres long and must not be confused with UC-CMC020-01A.

No software or firmware is installed in the cable. Configure node addresses, baud rate and data mapping in the connected devices. Select Delta CANopen Builder according to the engineering tools supported by the controller or communication module.

Editor's Note

The 020 code identifies this two-metre model; 200 identifies the twenty-metre version. Order by the complete code. Allow for cable-duct bends and connector access rather than measuring only the straight distance between devices.

Connector fit alone does not verify the connection. Identify CANopen or DMCNET operation and the relevant pin functions first. Label existing connections before changing network equipment.

Disconnect both ends before continuity testing. Follow the diagram for signals, reference ground and shield connections. Gently move each cable entry while measuring to check for broken conductors or intermittent contacts.

For communication interruptions, check node addresses, baud rate and termination first, then compare with a known-good cable. Even a short cable may fail to communicate because of incorrect settings or a loose socket.

Do not wind spare cable around motor power wiring or strain the plugs. Inspect a used cable's latch, contacts and outer jacket, and test stable communication with suitable devices where possible.

PDF and wiring documentation

Use Delta PLC accessories files for cable and accessory resources, and Delta PLC and HMI manuals for device network settings. The cable guide's printed page 3-7 covers applications; page 3-9 contains Figure 1 and the pin definitions.

Related topics

Delta CANopen cables · Delta UC-CMC015-01A · Delta UC-CMC030-01A · Delta TAP-CN03 · Delta TAP-TR01

Return to Delta PLC accessories. Browse controllers in the Delta PLC category and available devices under second-hand Delta products.

External references: Delta PLC/HMI Cable Selection Guide (archived manufacturer document) · Delta Download Center