6ES5 451-4UA14

Siemens 6ES5 451-4UA14 — 32-Channel 24 V DC Digital Output Module

The Siemens 6ES5 451-4UA14 is a 32-channel, 24 V DC/0.5 A digital output module for S5-135U/155U controllers in the SIMATIC S5 family. This S5 digital output module applies field commands from the PLC central controller through transistor DC outputs. Galvanic isolation covers one group of 32 outputs.

Supply and output groups

The permissible load-supply range is 20–30 V DC, and the output-current range is 5 mA–0.5 A. Each group of eight outputs permits a maximum combined switching current of 4 A. These eight-channel fuse groups must not be treated as separate galvanic isolation groups.

Total load, temperature and cooling

For the exact 451-4UA14, the CSA certificate specifies 16 A total at 55 °C with a fan, 8 A total at 55 °C without a fan and 16 A total at 35 °C without a fan. Check cabinet temperature and cooling before applying the 0.5 A channel rating across every output.

Load selection and output behaviour

For DC loads such as relay and contactor coils, consider switching conditions alongside operating current. OFF-state residual current is 0.5 mA maximum. In PLC input/output design, do not assume identical switching-frequency allowances for resistive and inductive loads.

F enable input and H+ fault signal

The module has a 24 V DC F+/F− enable input. With jumper X20 fitted, the enable input is active; this is the factory setting. If a command is present without an output response, check the enable condition as well.

A red LED per eight outputs provides short-circuit indication. H+ is the common short-circuit signal for all outputs, limited to 10 mA maximum. A suitable digital input can monitor it; it is not a field-load drive output.

UA14 fusing and front connector

The 451-4UA14 requires one 7 A fast fuse per eight outputs. Distinguish this fuse selection from the 6.3 A slow type specified for the 451-4UA13. The fuse rating is not the permitted load current of an individual output.

The module is 20 mm wide and uses a 42-pin front connector. The screw-terminal 6ES5 497-4UB31 and crimp-terminal 6ES5 497-4UA12 are single-width connector options. Check the cable and terminal arrangement against the existing diagram and preserve the layout in the S5 rack.

Fault finding and replacement

During PLC debugging, check the command, F enable condition and affected group's supply in sequence. Interpret multimeter readings alongside behaviour under load. Review grounding and cable routing when assessing noise immunity. Work on modules and front connectors with both PLC and field supplies disconnected.

Comparison with related models

The 6ES5 454-4UA14 is a 16-output, 24 V DC/2 A model. The 6ES5 453-4UA12 provides individual isolation across 16 outputs. Although the 6ES5 451-7LA12 has 32 outputs, it belongs to the S5-115U/F hardware family. Matching channel counts alone do not establish wiring or mechanical compatibility.

Editor's note

Count all 32 outputs, but give the load calculation equal attention. Cabinet temperature and a fan that actually works directly affect this board's total loading.

If one group stops working, first check the supply, fuse and loads for those eight outputs. One field fault should not lead to setting aside a sound board.

If every output stays quiet, check the F enable input and X20 setting too. Photographs of the old board's jumper and wiring help when fitting a spare.

The UA13 and UA14 have similar names, but their fuse characteristics differ. Reading the complete suffix and selecting the right part is easier than tracking down another failure.

When checking a used board, test all four groups of eight outputs under load. Keep the result with the S5 system information to make the next service easier.

OtomasyonAVM resources and PDFs

+ Start with the OtomasyonAVM S5 PDF archive.

+ Exact UA14 specifications and wiring appear in S5-135U/155U System Manual, 8-50–8-51; temperature-dependent total loads appear in CSA Certificate 1232105, PDF page 9.

Related topics

+ 451-4UA13 · 454-4UA14 · 453-4UA12 · 451-7LA12.

+ 497-4UB31 screw-terminal connector · 497-4UA12 crimp-terminal connector · S5 cables and connectors.

Browse SIMATIC S5

+ S5 digital output modules · SIMATIC S5 central controllers · Siemens S5 main page.

+ Used Siemens automation equipment.

Siemens and external references

+ Siemens S5-135U/155U System Manual — C79000-G8576-C199-07: pages 8-50–8-51, PDF pages 364–365; UA14 column, load limits, fusing and F/H connections.

+ CSA Certificate 1232105 — Siemens S5: PDF page 9; total-load conditions at 35 °C and 55 °C, with and without a fan.

+ Siemens ST 50 Catalog — 1998: pages 4/39–4/42; technical comparison, 42-pin front connector and terminal arrangement. An externally archived copy of the manufacturer catalog.