6ES5 415-7AB21
Siemens 6ES5 415-7AB21 — 8-Channel 220 V AC Digital Output Module
The Siemens 6ES5 415-7AB21 is an 8-output, 220 V AC/2 A digital output module used in S5-110A and S5-110S/B systems within the SIMATIC S5 family. Its digital output stage uses triacs to apply commands from the central controller to field loads with optocoupler galvanic isolation.
Operating voltage and total loading
The permissible field-voltage range is 176–264 V AC, with a maximum output current of 2 A per channel. Total loading is rated 100% at 20 °C and 50% at 55 °C. Across eight channels, these limits correspond to 16 A and 8 A total, respectively.
Switching and contactor selection
Maximum switching frequency is 20 Hz for resistive loads and 2 Hz for inductive loads. Turn-off occurs at AC current zero. The manufacturer states that 3T1-series contactors cannot be driven by this model; voltage and current labels alone are insufficient for coil selection.
Residual current and fusing
Maximum OFF-state residual current is 10 mA AC. Consider this when checking the release behaviour of small relay coils. The manual specifies a 6.3 A FF, very-fast fuse for short-circuit protection. Its rating does not increase the channel's 2 A load limit.
Mounting and front connections
The module snaps onto a socket connector on the S5-110 mounting rail. Check the rack and rail arrangement and front connections and cabling against the existing system drawing. Disconnect both control and AC field supplies before replacing the board or working on connections.
Address and LED checks
When reviewing the PLC input/output arrangement and program, match the rail's address coding to the existing project. Front LEDs are driven by the bus; an illuminated LED alone does not confirm the presence of field voltage or load current.
Fault finding
During debugging, check the command, field supply, fuse and load in sequence. Interpret an unloaded multimeter voltage reading alongside measurements under a suitable load. Review grounding and cable routing when checking for electrical interference.
Comparison with related models
The 6ES5 415-7AB11 is rated 115 V AC, the 6ES5 415-7AA31 24–48 V AC, and the 6ES5 410-7AA11 24 V DC. The 6ES5 417-7AA21 uses relay outputs. Confirm voltage, switching technology and connection suitability before selecting a replacement.
Editor's note
Remember that this board has 220 V AC triac outputs. Take a moment to check the complete code before reusing wiring from a 24 V DC board or a dry-contact relay.
If an LED lights but the load stays off, do not condemn the board straight away. The LED shows the command side; inspect the field supply, fuse and load circuit separately.
When a fuse needs replacing, preserve the 6.3 A FF characteristic. Check the wiring and connected load before considering another fuse; a higher rating is no cure for the original fault.
Each channel is rated 2 A, but cabinet temperature matters too. At 55 °C, all eight outputs share an 8 A total limit; include that condition in the load calculation.
For a used board, test both turn-on and release behaviour on all eight channels with suitable loads. Keep the results with the S5 system information so the next service has a useful reference.
OtomasyonAVM resources and PDFs
+ Siemens S5 pages and the OtomasyonAVM shared S5 PDF archive.
+ The exact model appears in S5-110S/B Operating Instructions, page 10 and S5-110A Operating Instructions, page 1.13. S5-110A pages 1.6–1.7 explain LED operation and triac output behaviour.
Related topics
+ 415-7AB11 · 415-7AA31 · 410-7AA11 · 417-7AA21 · 405-7AB21 input module.
Browse SIMATIC S5
+ S5 digital output modules · SIMATIC S5 central controllers · Siemens S5 · Used Siemens equipment.
Siemens and external references
+ Siemens S5-110S/B Operating Instructions — GWA 4NEB 807 2121-02: English, page 10/PDF page 12; exact 7AB21 column and 3T1 restriction.
+ Siemens S5-110A Operating Instructions — GWA 4NEB 807 0690-02: English, pages 1.6–1.7 and 1.13/PDF pages 10–11 and 17; LEDs, triacs, residual current, FF fusing and total loading.
+ Siemens S5-110S/B Betriebsanleitung — GWA 4NEB 807 2121-01: German, page 10/PDF page 12; specification cross-check. Links lead to externally archived copies of manufacturer documents.