6ES5 405-7AB21
Siemens 6ES5 405-7AB21 — 8-Channel 220 V AC/DC Isolated Digital Input Module
Siemens 6ES5 405-7AB21 is an 8-channel, galvanically isolated digital input module in the SIMATIC S5 family. The manufacturer’s S5-110S/B table specifies a nominal input voltage of 220 V AC/DC. This input module belongs to the S5-110A peripheral range and reads field status signals in a suitable S5-110S installation using the correct sockets and mounting arrangement.
Typical sources include relay contacts, limit switches and sensors with suitable electrical outputs. When choosing an inductive proximity switch, check its output voltage as well as its sensing characteristics. The manual specifies AC BERO proximity switches for this AC input range; match the sensor’s operating and leakage-current characteristics to the input.
Input levels and AC/DC current
The specified logic-0 range is 0–70 V AC/DC and the logic-1 range is 170–264 V AC/DC. Do not use the 70–170 V region as a defined logic level. Input current at logic 1 is 15 mA AC or 2.4 mA DC. Assess input voltage measurements and the field supply according to the actual AC or DC circuit.
Switching delays and simultaneous loading
The specified 0-to-1 delay is 2.3–13 ms, while the 1-to-0 delay is 2–20 ms. Include both input delay and CPU scan timing when assessing short pulses.
At 1.2 times nominal voltage, the manual specifies a total loading capability of 75%, referred to the sum of all input currents. Assess applied voltage and simultaneously active inputs together; the specification is expressed in terms of total input current.
Isolation, mounting and field wiring
Field signals are transferred to the PLC electronics through optocoupler-based galvanic isolation. Front LEDs indicate channel states. Approximate module weight is 0.4 kg. Inspect the correct mounting and socket arrangement together with the S5 connecting cables.
In the S5-110S arrangement, sockets fit onto the mounting rail and modules fit onto those sockets. Preserve the rack’s grounding connection and the insulation of the field wiring. Match terminal connections to the module markings and the machine’s electrical drawings.
Addressing through socket position
Addressing in this peripheral arrangement depends on socket and module position. The eight channels are processed as the eight bits of an input byte in the PLC program. For example, an input assigned byte 0 can be shown as I0.0–I0.7; this is not a fixed factory address. Check PLC addressing against the existing socket coding and program.
Do not install two input modules at the same input address. If the installation includes interface modules or an expansion arrangement, review the address area and connection chain together against the existing project.
Compare the actual input voltage, channel LED and program bit in that order. During Siemens S5 troubleshooting, a fault affecting all inputs also calls for checks of the field supply, socket connections and peripheral cable.
Voltage and function differences between similar codes
6ES5 405-7AB11 is rated for 115 V AC/DC inputs. 6ES5 400-7AA13 is a 24 V DC input module, while 6ES5 401-7AA13 provides 24 V DC inputs with a group signal. Compare voltage ratings and functions individually, and use the full label code when selecting a replacement for the 405-7AB21.
Editor’s note
Confirm the 7AB21 suffix first. A 115 V module from the same 405 family can be easy to confuse with this 220 V version. Obtain clear front-label, rear-label and socket-marking photographs before choosing a spare.
A 24 V test cannot establish its condition. The defined logic-1 range starts at 170 V. A test intended for low-voltage PLC inputs will not prove that this module is faulty or healthy; use a suitably protected bench and qualified personnel.
Investigate open-circuit voltage readings carefully. AC sensor leakage or capacitive coupling along a cable can produce misleading measurements. Measure against the correct reference and compare the channel LED with the PLC bit.
Give the socket and address the same attention as the board. Oxidised contacts, incomplete seating or the wrong address position can make a healthy module appear faulty. Isolate power before inspection and investigate any burning or cracked insulation.
Assess all eight channels on a used module. Record the on and off state of each input separately. A few working channels do not establish the condition of the whole module, and module or field connections must not be removed while the 220 V circuit is energised.
OtomasyonAVM resources and PDFs
+ About Siemens S5 PLC — systems and module structure
+ S5 digital input modules — model pages
+ Our general SIMATIC S5 PDF archive — existing manual and file index.
Related topics
Voltage fundamentals · Relay and contact operation · Grounding connections
Browse SIMATIC S5
S5 digital input modules · SIMATIC S5 · Siemens S5 PLC · Used Siemens equipment
Siemens and external references
+ SIMATIC S5-110S/B Operating Instructions — GWA 4NEB 807 2121-02, English: §1.4, printed p. 9 / PDF p. 11; exact 405-7AB21 specifications. S5-110A peripheral use: printed p. 2 / PDF p. 4; module and LED description: printed p. 8 / PDF p. 10; socket/rack addressing: §2.3, printed pp. 15–16 / PDF pp. 17–18.