6ES5 700-2LA12

Siemens 6ES5 700-2LA12 SIMATIC S5 CR 700-2 central rack

The 6ES5 700-2LA12 is the CR 700-2 mounting rack for a SIMATIC S5-115U central controller. Its layout includes PS, CPU, module positions 0–6 and IM. Read the S5 power supply label to identify the fitted PS 951. Siemens ST 50 lists CPUs 941 through 945 for this rack. Use the CPU-specific layout when fitting a CPU 944 or CPU 945.

Slots and mounting

The S5-115U configuration accommodates up to seven I/O modules. The rack measures 483 × 303 × 47 mm (W × H × D) and weighs 5 kg. Siemens specifies 19-inch cabinet mounting. Allow additional depth for the installed cards and front connectors.

Check Figure 3-5 and each module manual for the positions of digital inputs, digital outputs, combined digital I/O, analog I/O and communications modules. For a CP 524, check both slot assignment and power supply requirements. The ST 50 table specifies IM 306 for block-type analog modules in slots 4, 5 and 6. It excludes slot 6 for the 434-4 digital input module.

Centralized and distributed expansion

In S5-115U, centralized expansion uses the IM 305 or IM 306. The manual lists an overall maximum of three centralized expansion units. The actual limit depends on the interface and cable. In distributed configurations, the IM 304 and IM 308 offer different connection options. Verify the remote S5 interface, cable and any terminator against the corresponding Siemens drawing.

The ER 701-1, ER 701-2 and ER 701-3 expansion racks have different supply and interface layouts. When selecting a spare central rack, compare the labels of the CR 700-1, CR 700-3 and the S5-115F CR 700-2F 6ES5 700-2LA22. For cabinet cooling, record the label of any fitted long-rack fan and the power supply load.

For S5-115H, ST 50 lists the same 6ES5 700-2LA12 with the CPU 942H and up to six I/O modules. Expansion is centralized in this layout. The IM 304 or IM 324R links the two central controllers, a separate role from distributed expansion in the S5-115U layout.

Editor’s note

1. Map the slots before removal. After qualified personnel isolate cabinet and field supplies, photograph the PS, CPU and IM labels, cards in positions 0–6 and their numbered front connectors.

2. If the CPU and all local cards fail together, check the shared path. Have qualified personnel check the PS 951 supply and status indicators, then isolate power before inspecting the PS and CPU connectors. Record the findings before replacing the rack.

3. If local cards work and the remote rack drops out, trace the link. Check the central IM, remote IM, cable ends and remote supply in order. Compare the terminator with the installation drawing.

4. For an analog-only fault, check the slot and interface together. Verify the IM 306 requirement and project address for a block-type analog card in positions 4–6. Record the existing address before moving any card.

5. Ask for a slot-by-slot check on a used rack. Request close-up photos of the label, PS/CPU/IM connectors and positions 0–6. The test record should list the CPU, interface and positions tested.

To offer a rack for sale, send its full part number, quantity, condition, label and connector photos, and asking price to otomasyonavm@gmail.com.

Siemens PDF documentation

The exact order-number data sheet (EN) uses the phrase “expansion unit” in its short description. For the central rack layout, see S5-115U Figure 3-5 (EN) and the technical table on p. 15-6 (EN). ST 50, S5-115U p. 3/61 (EN) · S5-115H Figure 3-3 (EN) · ST 50, S5-115H p. 3/68 (EN) · OtomasyonAVM S5-115 PDF archive

Related topics

Siemens S5 PLC overview · SIMATIC S5 CPU models · IM 306 interface

Second-hand Siemens navigation

SIMATIC S5 racks · SIMATIC S5 · Siemens S5 PLC · Second-hand Siemens