Delta ASDA-B2

Delta ASDA-B2 AC Servo Drive Series

Delta ASDA-B2 is an AC servo drive series for single-axis motion, with models from 100 W to 3 kW. It works with compatible Delta ECMA servo motors. For a replacement or a new installation, check the complete motor order code, encoder type and drive nameplate together.

ASDA-B2 user manuals

Delta ASDA-B2 User Manual (PDF, English, 2023) · 351 pages. See printed page 1-5 for motor matching, 1-8 for control modes, 3-37 for CN3, 5-7 for the JOG trial and 6-8 for electronic gearing. Chapter 10 covers alarm diagnostics.

2010 archive edition (PDF, English) · 313 pages. Use it to compare against documentation for older installations. See the Delta Servo Manuals archive for other series.

Drive and motor selection

100–750 W: ASD-B2-0121-B (100 W), ASD-B2-0221-B (200 W), ASD-B2-0421-B (400 W) and ASD-B2-0721-B (750 W). 1–3 kW: ASD-B2-1021-B (1 kW), ASD-B2-1521-B (1.5 kW), ASD-B2-2023-B (2 kW) and ASD-B2-3023-B (3 kW).

When matching the motor and drive, check the supply phase, motor current, feedback type and cable part numbers alongside the power rating. If resizing the motor, calculate the load inertia and transmission ratio. On an axis with a planetary gearbox, mechanical backlash can affect position accuracy after a reversal.

Position, speed and torque control

The manual also calls P mode PT. In this mode, the drive receives the external pulse position command through CN1. Match the PLC and drive pulse and direction format. Then verify the electronic gear ratio at P1-44 and P1-45 and compare commanded travel with actual movement.

S speed and T torque modes can use a ±10 V analog command or an internal reference. Verify the required speed or torque control mode at P1-01. During testing, monitor command and feedback values to evaluate the speed loop and current loop.

ASDA-Soft and field connections

CN1 carries commands and I/O, CN2 connects the motor encoder, and CN3 carries RS-232/RS-485 serial communication. For ASDA-Soft, choose a serial cable that matches the CN3 pinout. For PLC-based axis control, record the command format, limit inputs and home reference from the existing project before replacing the drive.

Editor’s note

Ask for the drive and motor nameplates together. For a used 750 W set, compare the complete drive code with the ECMA motor’s encoder, brake and shaft options. Confirm whether the CN1 plug, motor power cable and CN2 encoder cable are included.

Read the fault history before resetting. Back up the P4-00–P4-04 records and parameters. If AL011 occurs at startup, check the motor match and CN2 connection. If it occurs when the cable chain moves, inspect the flexing section and connector contact. Include shielding and signal noise in your feedback checks.

Test bench JOG and PLC commands separately. Under safe test conditions, secure the motor, uncouple it from the load and test the motor-drive set with low-speed JOG. If JOG works and the PLC command produces no movement, check the CN1 command line, Servo ON and limit states, then check P1-00 and P1-01.

For AL009, compare commanded and actual position. If the command count advances and the axis falls behind, check for binding, load and motion-profile issues. If the travel is consistently off by the same ratio, check the electronic gearing and the PLC’s pulse-to-distance calculation.

Record when AL002 occurs during deceleration. Review the deceleration time, load inertia and regenerative braking arrangement. Use the table for the complete ASD-B2 code when selecting a resistor.

Check the load and mechanics first if AL006 or vibration occurs. During maintenance, inspect the coupling, bearings and mechanical friction. Record whether the vibration repeats at the same position. Back up the existing settings before considering auto-tune or changing servo loop gains.

Related Delta equipment

Use the nameplate series code to find the corresponding information for Delta ASDA-B2-F, Delta ASDA-B2L, Delta ASDA-B3 or Delta ASDA-A2. For the command and operator interface, see Delta PLCs and Delta DOP-100 panels.

Browse · Delta servo drives · Delta Automation

External reference

Original Delta ASDA-B2 User Manual, 2023