Delta ADPCAB03A
Delta ADPCAB03A
Delta ADPCAB03A is a 30 cm RS-485 connection cable between the ADP485-01 adapter and a Delta ASDA-A servo drive. The instruction sheet uses ASD-A, while catalogues identify the drive family as ASDA-A. See Delta DVP other accessories and Delta PLC accessories for the related product groups.
Male DB9 and 6-pin 1394-style connections
The manufacturer's cable drawing identifies male DB9 and male 1394 ends. The ASDA-A communication connector has a 6-pin 1394-style form. This application carries RS-485; the connector shape does not establish FireWire protocol or compatibility with a computer IEEE1394 port.
A DB9 housing alone does not establish RS-232 signalling. Follow the Cable Connection drawing in the ADP485-01 instruction sheet. It includes bridged connections, so do not treat this as a simple pin-for-pin cable. Distinguish contact-face views from solder-side views when identifying pins.
Role of the 30 cm cable
ADPCAB03A makes the short connection between the servo drive and its nearby adapter. Its 30 cm length is separate from the total RS-485 network length. Plan trunk routing, node positions and termination independently. The cable does not perform USB or protocol conversion.
The protection components and selectable 120 Ω termination specified for ADP485-01 belong to the adapter. They are not cable isolation ratings or internal cable electronics. Arrange network termination according to the two physical ends and any existing device resistors.
ADPCAB03A versus ADPCAB03B
Delta ADPCAB03B is the 30 cm cable specified for ASDA-B, with a mini-DIN drive-end connector in the manufacturer's drawing. ADPCAB03A serves the ASDA-A / 1394-style connection. Preserve the A/B suffix when selecting the cable.
Recheck cable selection when changing to another generation, such as Delta ASDA-A2 or Delta ASDA-B2. Similar family names or connector appearances do not establish compatibility of an older ASDA-A cable with every newer drive. See Delta servo drives for the related families.
RS-485 settings and computer access
The controller and drive must use compatible communication rates and data formats, with a unique station address for each device on the line. On the Delta DVP PLC, Delta AS PLC or Delta AH PLC side, select the port, cable and communication instructions from the relevant CPU documentation.
Computer access through USB requires a suitable separate RS-485 interface. Review Delta IFD6500 and other Delta DVP interfaces, checking terminal wiring and protocol support. ADPCAB03A itself is not a direct USB programming cable.
Choose Delta WPLSoft, Delta ISPSoft and, where required, Delta COMMGR according to the PLC CPU's supported tools. Configure servo parameters from the drive's own manual. The cable itself requires no software or driver installation.
Editor's Note
Record the complete 03A suffix, servo label and adapter model when ordering. The A and B cables have the same stated length, but serve different connection arrangements.
Do not substitute a computer cable solely because its plug has a 1394 shape. Verify the drive communication socket and manufacturer wiring first. Likewise, do not build the DB9 end by copying an ordinary RS-232 pin assignment.
Disconnect both cable ends and remove the relevant supplies according to manufacturer shutdown instructions before continuity testing. Trace pins against the diagram; do not mistake intentional bridges for short-circuit faults. Avoid spreading small contacts with oversized meter probes.
If communication fails with an apparently intact cable, check rate, data format and station address in sequence. Record existing termination before changing switch settings. Change one item at a time so the cause remains clear.
Do not stretch the 30 cm cable tightly between devices. Inspect crushed sections and conductor damage near plugs when faults change with movement. Where possible, test a used cable through stable data exchange with the appropriate drive and adapter.
PDF manuals and connection documents
Use Delta PLC accessories files for adapter instructions and cable resources, and Delta servo manuals for the drive communication port. Consult Delta PLC and HMI manuals for controller-side documentation. Match the complete cable, adapter and drive codes within the same wiring arrangement.
Related topics
Delta ADP485-01 · Delta ADPCAB03B · Delta DVP communication cables · Delta DVP programming cables
Return to Delta DVP other accessories. Browse controllers in the Delta PLC category and available equipment under second-hand Delta products.
External references: Search the Delta Download Center using ADP485-01 and the drive's complete model code for manufacturer documentation.