6ES5 375-0LA41

6ES5 375-0LA41 Siemens SIMATIC S5 32 KB CMOS EPROM Memory Submodule

The Siemens 6ES5 375-0LA41 is a 32 KB (32,768-byte) CMOS EPROM 375 memory submodule for SIMATIC S5 equipment. It retains its contents when power is removed. Siemens specifies byte organisation and programming number 17 for the 0LA41. The full order number appears in the S5-95F, S5-115F and S5-115H memory tables.

In a CPU, the EPROM holds the approved STEP 5 user program for storage and recovery using the system’s documented procedure. In a supported communications processor such as the CP 521, the contents are prepared for that processor’s application. Record which CPU or CP the EPROM came from when archiving its program.

Which S5 systems list the 0LA41?

Siemens lists the 0LA41 in the S5-95F and S5-115F memory tables. For an S5-95F 8FA01, S5-95F 8FA02 or S5-115F CPU 942F, check that the manual covers the installed hardware revision. In dual-CPU configurations, Siemens requires the same memory submodule order number in both units.

The S5-115H system manual also identifies the 0LA41 as 32 KB, byte-organised, programming number 17. The two CPUs in a redundant S5-115H system must have memory submodules with the same order number.

The reviewed S5-100U manual lists the 1LA41 as the 32 KB EPROM in the ordering appendix for the CPU 100, CPU 102 and CPU 103 range. For the S5-115U, consult the applicable memory table for the CPU 941, CPU 942, CPU 943 or CPU 944. Match the selection to the full CPU order number and the relevant manual edition.

How is it used in a CP 521?

The Siemens manual covering the CP 521 SI 8MA21 and CP 521 SI 8MA22 lists the 0LA41 with a 2 × 16 KB organisation. Depending on the application, it can hold serial communications parameters and printer message texts. The CP 521 BASIC manual also lists the 0LA41 as a supported EPROM. Use the project file for the installed BASIC processor when preparing its memory.

How is the EPROM programmed and checked?

Prepare the submodule offline on a compatible Siemens programming device with the appropriate EPROM socket or adapter. If the PG prompts for a programming number, select 17 for the 0LA41. Before reprogramming a used EPROM, read and save its contents, then use a suitable UV eraser. After programming, read back or compare the contents on the PG against the project file.

How do the similar memory codes differ?

The 375-0LA15 is an 8 KB EPROM with programming number 11. The 375-0LA21 is a 16 KB EPROM with programming number 12. The 375-1LA41 also holds 32 KB. Siemens assigns it programming number 417 in the S5-115F and S5-95F tables.

The 375-0LC31 is an electrically erasable 8 KB EEPROM. The 373-0AA41 is a 32 KB EPROM from the separate 373 series. When choosing a spare, verify the memory family, the full order number and the programming number together.

Editor’s note

Before removal, photograph the 6ES5 375-0LA41 label, the CPU or CP that holds it and the insertion orientation. One cabinet can contain EPROMs for several different devices.

Read the original EPROM on the PG before erasing it. Save the readout as a separate backup with the machine name, program revision and memory order number.

Check programming number 17 on the PG. After writing, complete a readback or comparison and add the project revision to the memory label.

On a redundant or fail-safe system, match both memory order numbers and the approved program contents. Follow the installed system’s service and commissioning procedure for the replacement.

If the expected program revision fails to load at startup, check the EPROM contents first and then the CPU or CP’s memory loading procedure. A module can read correctly on the PG and still contain a project built for a different device.

OtomasyonAVM resources and PDFs

Siemens SIMATIC S5 PLC guide · SIMATIC S5 memory submodules

OtomasyonAVM SIMATIC S5 PDF archive

SIMATIC S5-115H system manual · Memory submodule table and 0LA41 programming number

Related topics

375 series EPROMs · 6ES5 375-0LA15, 8 KB · 6ES5 375-0LA21, 16 KB

Memory in communications processors · CP 521 SI 6ES5 521-8MA22 · CP 521 BASIC 6ES5 521-8MB12

Browse SIMATIC S5

Used Siemens SIMATIC S5 equipment › SIMATIC S5 › S5 memory submodules

Siemens documentation and external references

Siemens SIMATIC S5-95F system manual · 0LA41 memory entry and matching submodule requirement

Siemens SIMATIC S5-115F system manual · Table 2-3, EPROM types and programming numbers

Siemens CP 521 SI Communications Processor manual · Table 2-2a, 2 × 16 KB organisation for the 0LA41

Siemens CP 521 BASIC manual · Table 2-3, supported earlier EPROM models

Siemens SIMATIC S5-100U system manual · Appendix D, CPU memory ordering data

Siemens SIMATIC S5-115U system manual · Table 2-8, CPU memory submodules