6ES5 375-0LA15

Siemens 6ES5 375-0LA15 SIMATIC S5 8 KB EPROM Memory Submodule

The Siemens 6ES5 375-0LA15 is an MS375 memory submodule in the SIMATIC S5 range. It holds 8 KB (8,192 bytes) in a UV-erasable EPROM. The Siemens PG 615 table lists it for S5-100U, S5-101U and S5-115U systems. In a compatible device, it retains the program or configuration through a power loss.

What the module holds depends on the device it serves. A CPU can use it for a STEP 5 program, a printer processor for serial settings and message texts, and an OP 396 for an operator project configured in COM 396. When sourcing a spare, confirm the order number and identify the device for which the EPROM was programmed.

Which CPUs and communications devices use this EPROM?

For the S5 CPU range, use the programming-device table alongside the memory table for the installed unit. In an S5-100U, read the label to distinguish versions such as the CPU 103 8MA01 and CPU 103 8MA02. The S5-101U accessories table lists the 0LA15 explicitly. For S5-115U processors such as the CPU 941 and CPU 942, check the full CPU order number, revision and memory receptacle.

In the S5 communications range, Siemens lists this EPROM in the manuals for the CP 521 Printer/ASCII, CP 521 SI 8MA21, CP 521 SI 8MA22 and CP 521 BASIC. The Printer/ASCII version can use up to 8 KB of submodule memory. The OP 396 manual lists the 0LA15 as a COM 396 user submodule for receptacle 2.

How do you read, erase and program the EPROM?

First read the existing contents with a compatible Siemens PG or EPROM programmer and save them to a separate file. Use a UV eraser to clear the EPROM before reprogramming it. Run a blank check before writing, then read the module back and compare it with the source file.

Select the programming number from the table for the equipment in use. The CP 530 manual shows the 0LA15 as selection 5 in COM 530/615. The CP 521 SI programming table lists 11. The 6ES5 734-2BD20 and 6ES5 734-2BF00 are examples of S5 PG cables for retrieving a project from a PLC. The EPROM itself is written in the programmer’s memory receptacle.

How do the similar memory order numbers differ?

The 6ES5 375-0LA21 is a 16 KB EPROM, and the 6ES5 375-0LA41 is a 32 KB EPROM. The 6ES5 375-1LA15 is an 8 KB CMOS EPROM with programming number 411 in the CP 521 SI table. Check the host’s memory table before selecting a larger card or a different EPROM version.

The 6ES5 375-0LC31 is an electrically rewritable 8 KB EEPROM. The 6ES5 373-0AA21 belongs to the separate 373 EPROM family. Siemens also documents a specific jumper conversion from the older 0LA11 to 0LA15 for use with the OP 396. If a used card has been relabeled, confirm its identification on the programmer.

Editor’s note

Photograph the full order number on the EPROM and the label on the CPU, CP or OP that holds it.

Save a separate readout of the working EPROM before erasing it. The current CPU project and the EPROM contents may be from different revisions.

Select 0LA15 and 1LA15 by their respective order numbers on the programmer. If a write fails, start by checking the selected module type and programming number.

Switch off power before inserting or removing the submodule. Check its orientation and receptacle. Leave the UV window label in place during reading and storage.

Read back and verify the programmed card. On the first test, check program startup on the CPU, the communications settings on the CP or the screen project on the OP, as applicable.

OtomasyonAVM resources and PDFs

See the Siemens SIMATIC S5 PLC overview and the SIMATIC S5 memory submodules section for related hardware.

SIMATIC S5 system manuals and PDF archive.

Related topics

MS375 0LA21 16 KB EPROM, MS375 0LC31 8 KB EEPROM and CP 521 Printer/ASCII processor.

Browse the S5 range

S5 memory cards and SIMATIC S5 family.

If you have a module to sell, send a label photo, quantity and working condition to otomasyonavm@gmail.com.

Siemens and external technical references

Siemens PG 615 manual, Table 2.9 – Programmable memory submodules (German PDF)

Siemens CP 521 Printer/ASCII manual – Memory options and UV erasure (PDF)

Siemens CP 521 SI manual – Submodule capacities and programming numbers (PDF)

Siemens OP 396 operator panel manual – COM 396 user memory and receptacle 2 (PDF)