Simatic S5 Special modules
Siemens SIMATIC S5 Special Modules and Control Accessories
Siemens SIMATIC S5 special modules cover temperature control, valve control, closed-loop regulation, high-speed counting, timing, identification and service tasks. This section also includes display interfaces, test equipment and a configuration package.
Compare the complete order number, system family, I/O type and existing application when selecting equipment. Items in this section have different host systems and mounting requirements. Check S5-90U/95U/100U modules separately from older S5-110A, S5-130 or S5-210 equipment.

IP 244 temperature control and IP 245 valve control
6ES5 244-3AA13 and 6ES5 244-3AA21 belong to the IP 244 temperature controller family. Check measurement inputs, compensation, control outputs and CPU data exchange for the exact version. Match the FB 162 version to the module hardware and firmware before transferring an existing configuration.
6ES5 245-1AA12 is in the proportional valve control group; 6ES5 245-1AB12 is in the servo valve control group. Valve type, coil characteristics and control method determine the required hardware. Compare the installed valve and drive arrangement against the exact module documentation.
IP 252 and IP 262 closed-loop controllers
6ES5 252-3AA11 and 6ES5 252-3AA13 are IP 252 closed-loop control modules. Analog measurements, control outputs, COMREG configuration and PLC data exchange form part of the application. Check documented transition requirements before reusing another version’s parameters or connections.
6ES5 262-8MA12 is the current-output K-type IP 262; 6ES5 262-8MB13 is the S-type IP 262 with four binary output pairs. The S-type can be configured for heating/cooling pulses or open/stop/close actuator control. 6ES5 262-8MB12 is an earlier S-type version; compare the hardware and documentation scope of 8MB12 and 8MB13 separately.
IP 242, IP 242A and IP 242B counter modules
6ES5 242-1AA12, 6ES5 242-1AA13 and 6ES5 242-1AA21 are separate order numbers in the IP 242 counter group. Check pulse input levels, counting method, control inputs and PLC addressing for the exact model.
6ES5 242-1AA31 and 6ES5 242-1AA32 belong to the IP 242A group; 6ES5 242-1AA41 is an IP 242B. Counter width, channel functions, input filtering and function blocks depend on the version. Similar suffixes or front connectors are insufficient evidence of interchangeability.
IP 281 counter base and additional counter submodule
6ES5 281-4UA11 is an IP 281 counter base module with a 24 V encoder supply. 6ES5 281-4UB12 belongs to the additional counter submodule group. Verify the base-module generation and submodule pairing; compatibility of every 4UB12 with a 4UA11 must not be assumed.
380, 385 and 390 timer/counter equipment
6ES5 380-8MA11 is a two-channel timer covering 0.3–300 seconds. The 385A 6ES5 385-8MA11 provides two independent counting channels rated up to 500 Hz. The 385B 6ES5 385-8MB11 is a different high-speed counter: distinguish its 500 kHz limit with 5 V RS-422 signals from its 25 kHz limit with 24 V signals.
6ES5 390-5AA22 belongs to the S5-130A/130K timer and down-counter group, providing 56 preset timers, 8 stopwatches and 16 down counters. 6ES5 382-0AA32 is a Type I adapter set used with older timer/counter arrangements. Check their host systems and mounting separately from smaller S5 bus modules.
Display and system interfaces
6ES5 250-1AA31 and 6ES5 251-1AA11 are associated with S5-210 display/keyboard and serial interface equipment. Match the controller, display, keyboard, cables and application software together. Establish protocols and pin assignments from the relevant documentation.
6ES5 255-3AA11 and 6ES5 255-3AC11 belong to the IP 255 display/monitor interface group; 6ES5 256-3AA11 and 6ES5 256-3AB11 to the AS 256 DIMOS/VISRAM interface group. Preserve the required monitor signal format, cabling and configuration. A physical video adapter alone cannot convert incompatible signal formats.
MOBY identification system interfaces
6ES5 254-4UA21, 6ES5 254-4UB11 and 6ES5 254-4UB21 are MOBY identification system interfaces. Compare MOBY-M and MOBY-SP designations with the associated reader/writer and system hardware. Supply requirements, channels and connector pins must be checked for the exact version.
Positioning hardware and the IP 247 configuration package
6ES5 246-4UA21 belongs to the IP 246I incremental-feedback positioning family. 6ES5 247-5AA11 is the German-language IP 247 configuration package, associated with COM 247, the relevant standard function blocks and documentation. Check the software environment, original media and licence separately from hardware modules.
Programmer adapter and test modules
6ES5 325-0UA11 belongs to the FOX PG-M programmer adapter group; 6ES5 330-7AB11 is an S5-110A test module. The 330 diagnostic module 6ES5 330-8MA11 is different equipment. Match the programmer, CPU family, cables and intended service task.
Testing used special modules
Compare the complete model, quantity, working/faulty condition, readable nameplate photographs and price. Specify which analog channels, pulse inputs, valve outputs, interfaces or parameter-retention functions have been tested. Powering up the board alone does not establish that its special function works.
Editor’s note
Start with the required task. A temperature controller, valve controller and high-speed counter perform different functions. Record the old module’s complete nameplate, connected equipment and rack position before choosing a replacement.
Before removing a working controller, back up parameters, setpoints, recipes and PLC blocks. A sound spare IP 244, IP 252 or IP 262 still requires the configuration that makes the machine operate correctly.
Distinguish IP 262 current outputs from binary output pairs. Treat proportional and servo valve connections separately as well. Identify what the output drives before transferring field wiring.
For counters, check more than the headline frequency. 5 V RS-422 and 24 V pulse inputs have different limits. Encoder supply, filtering, direction and channel arrangement must suit the application; IP 281 submodule generation also needs checking.
For older display and MOBY interfaces, assess the cables, connected devices and software with the board. Ask about media and licensing for a configuration package. Packaging or an order number alone does not establish that a working installation is available.
Agree the test scope and included items before buying used equipment. Workshop testing is possible, with the method determined by the module and available equipment. All sales require an invoice; returns are not accepted. To offer S5 equipment for sale, send the model, quantity, condition, nameplate photographs and asking price to otomasyonavm@gmail.com.
OtomasyonAVM resources and PDFs
For system background, see About Siemens S5 PLCs, the SIMATIC S5 main page and S5 CPU models. Review central units and expansion racks when comparing equipment from different generations.
Use the S5 system manuals and PDF files archive for connections, commissioning and function blocks. Compare the complete order number, hardware/firmware version and manual edition. Technical data for a newer family member must not be applied automatically to an older version.
Related topics
Review S5 positioning modules, S5 interface modules, S5 cables and connectors, S5 power supplies and S5 racks and mounting frames when selecting a special module.
Browse SIMATIC S5
+ SIMATIC S5 | Siemens S5 PLCs | S5 module groups | Used Siemens equipment | All used equipment
Siemens and external references
+ IP 244 Temperature Controller with FB 162 — C79000-G8576-C858-02; English.
+ IP 252 Closed-loop Control Module and COMREG — EWA 4NEB 811 0480-02; English.
+ IP 262 Regelungsbaugruppe — Handbuch — C79000-G8500-C5-06; 09/2001; German.
+ IP 242A / IP 242B Counter Module Manual — 6ES5 998-0KM21; Release 02; English.
+ IP 281 Equipment Manual — 6ES5 998-0KP21; Release 01; English.
+ S5-100U System Manual — Function Modules — EWA 4NEB 812 6120-02b; English.
+ Siemens SIMATIC S5 Catalog ST 50 — ST 50, 1998; English; Siemens catalogue, external archive copy.
+ Siemens SIMATIC S5-130/S5-150 Katalog ST 53 — ST 53 / E86010-K4653-E100-A3; 1985; German; Siemens catalogue, external archive copy.