6ES5 456-4UA12

Siemens 6ES5 456-4UA12 — 16-Channel AC Digital Output Module

6ES5 456-4UA12 is a 16-channel, 115–230 V AC digital output module for Siemens SIMATIC S5 S5-135U/155U systems. This model in the S5 digital output range has two galvanically isolated groups of eight outputs. The specified supply frequency is 47–63 Hz, with a permissible AC voltage range of 88–264 V.

This SIMATIC S5 module uses electronic AC outputs and must not be treated as a floating relay contact module. Check the S5 rack arrangement, cooling and output-group supplies together. The 2 A per-channel rating requires ventilated operation.

Cooling and group-current limits

For resistive and inductive loads with ventilation, the range is 40 mA–2 A per channel, with a maximum total of 6 A per four outputs. Without ventilation, the limits are 40 mA–1 A per channel and 4 A per four outputs. Calculate individual channel current and the four-channel total separately.

For lamp loads, the total limit per four outputs is separately specified as 2.5 A. For contactors and other coils, consider inrush current and the manufacturer’s load conditions. Sixteen outputs do not mean that all channels may simultaneously carry 2 A.

Fuses and fault isolation

The manual specifies one 6.3 A fast fuse per four outputs. Short-circuit protection is conditional on these fuses. When selecting a fuse, preserve its fast characteristic as well as its current rating. If a fuse keeps blowing, investigate the load and wiring before considering any replacement; do not fit a higher-rated fuse to hide the fault.

230 V supply and EMC filter

The relevant Siemens installation note requires a SIFI C or equivalent filter in the module’s 230 V AC load supply. Assess the EMC filter, supply routing and grounding as part of the cabinet arrangement. The filter requirement does not replace correct fusing or cooling.

Front connector and enable arrangement

The ST 50 catalog specifies two-slot width and a 20-pin front connector. The double-width, 20-pin screw-terminal option is listed as 6ES5 497-4UB42. When transferring S5 wiring and connectors, compare terminal numbers and group supplies with the exact model’s wiring diagram.

The F+/F− enable connection uses a jumper in the front connector; X20 determines whether the enable function is active. Record the original wiring and settings before replacement, then check the new module against the diagram on page 8-59. Do not troubleshoot by adding arbitrary enable bridges.

Off-state measurements and address checks

Maximum residual current in the “0” state is 5 mA. A voltage reading with a low-current load or high-impedance meter does not by itself prove a failed output. During troubleshooting, consider the minimum operating-current requirement and the actual output state of the S5 system.

Match the output address in the PLC program to the physical channel and group supply. Watch the command in the programming software; where necessary, follow the logic from the relevant digital input condition. Check the green status indication separately from actual switching at the load.

Comparison with similar order codes

When comparing the 6ES5 456-4UA11, verify the complete order code, hardware revision and wiring arrangement. The 6ES5 457-4UA12 is a DC output model, while the 6ES5 458-4UC11 uses relay outputs. An equal channel count does not establish equal voltage ratings or output technology.

Editor’s note

Start with the fan and the airflow path. Without ventilation, the channel limit drops to 1 A. If trouble started after adding loads to a cabinet that had worked for years, calculate the new total before blaming the board.

If four outputs disappear together, their fuse group is a sensible place to begin. A replacement fuse does not finish the repair if a coil or cable still has a fault. Keep the specified fuse rating rather than fitting a larger one.

A voltage reading with the output off can be misleading. This model has residual current and a specified minimum operating current. Interpret the measurement with the actual load in mind, so a serviceable board is not set aside unnecessarily.

If all outputs remain silent after replacement, compare the front-connector enable arrangement and the original X20 setting. A few clear photographs taken before removal can save considerable time here. Guessing at bridges only makes the fault harder to follow.

When buying a used Siemens 456-4UA12, ask for all sixteen channels to be tested with suitable AC loads. Establish whether the test used ventilation. Seeing it work briefly on a bench is a start; matching your load and cooling conditions is what makes the choice useful.

OtomasyonAVM resources and PDFs

+ S5 digital output modules · 497-4UB42 front connector · S5 racks and expansion units.

+ OtomasyonAVM shared Siemens S5 PDF archive. S5-135U/155U System Manual, §8.4.14, pp. 8-58–8-59 covers ratings and the enable diagram; ST 50 / 1998, pp. 4/40–4/41 covers load, filter and connector information. Both sources are in English.

Related topics

+ 456-4UA11 · 457-4UA12 · 458-4UC11 · Fuses · EMC filters.

Navigation

+ S5 digital output modules · SIMATIC S5 · Siemens S5 PLC · Used Siemens.

Siemens and external references

+ Siemens S5-135U/155U System Manual — English; C79000-G8576-C199-07, §8.4.14, pp. 8-58–8-59: 456-4UA12 specifications and wiring; p. 1-5: filter requirement.

+ Siemens ST 50 / 1998 — English manufacturer catalog, archived copy; pp. 4/40–4/41: 456-4UA12 and front-connector options.