6ES5 955-3NF42
Siemens 6ES5 955-3NF42 SIMATIC S5-135U/155U Power Supply
The Siemens 6ES5 955-3NF42 is a 955-series rack power supply for S5-135U/155U systems in the SIMATIC S5 family. It runs from a nominal 24 V DC input and accepts 19.2–33 V DC, including ripple. Its main rack rail is rated at 5.1 V DC / 40 A. The auxiliary rails are rated at 15 V DC / 2 A and 24 V DC / 2.8 A.
The unit supplies the system voltages for the modules in a compatible S5 central rack or expansion unit. If the whole rack drops out at startup, check whether the 24 V input sags under load. The 40 A rating belongs to the 5.1 V rail. At rated load the unit draws 20 A from a 24 V DC input, and Siemens specifies a 200 A peak inrush for 1 ms.
Checking the main and auxiliary rails
The 5.1 V and 15 V rails are regulated. Siemens specifies ±1.2% for the 5.1 V rail. If a CPU 928B or CPU 948B shows a fault, check that rail under load in the correct rack before swapping the CPU. The front test sockets marked 3 V = 40 A provide a voltage indication of 5.1 V rail current for temporary testing.
The 24 V output is coarsely stabilized. Its 2.8 A limit is shared between X2 and the front terminals. Use the cabinet drawings to trace sensor power for the digital inputs and field load power for the digital outputs. The wiring determines which circuits count toward that limit.
Which racks use this power supply?
Siemens pairs this part number with the 6ES5 188-3UA52 central controller and the 6ES5 185-3UA43 expansion unit. The 6ES5 188-3UA32 central controller and 6ES5 183-3UA22 expansion unit are listed with the 5 V / 18 A 6ES5 955-3NC42.
The 6ES5 188-3UA22 uses the 6ES5 955-3LF42, which also has a 40 A main rail and takes 120/230 V AC. Section 4.4 of the Siemens manual lists the 6ES5 135-3UA41 with the 6ES5 955-3NA12, rated for a 24 V DC input and a 5 V / 10 A main output. Match the input type, output rating and rack order number when selecting a replacement.
Wiring, fan alarms and memory backup
The DC supply connections are L+, M and PE. EN/UH is associated with the power supply enable circuit. Voltage Monitor monitors an external 24 V load supply. Document the existing S5 cables and connectors. Fit the unit in the specified housing with power isolated and the protective earth connection verified.
The 5V o.k., 15V o.k. and 24V o.k. LEDs show output status. A steady fan LED identifies a fan to check. If all three fan LEDs flash and Alarm is lit, check the filter and airflow. The F–R jumper determines whether certain fan and airflow faults shut down the power supply. If the rails are healthy and only the expansion unit is missing, check the S5 interface module and its connection separately.
With no external backup supply present, MB low points to the lithium battery or its compartment. RB low points to the internal rechargeable battery. The rack’s lithium backup battery is rated 3.6 V / 5 Ah, and the front external backup input is 4.5 V. Before a power interruption, check how the installed S5 memory card and backup arrangement retain the program.
Editor’s note
Ask for a photo showing the full 3NF42 suffix and a separate photo of the rack label. The 6ES5 955-3NF41 can carry the same input and main output ratings. Check the full part number against the rack configuration.
When the supply drops out at startup, check voltage at the unit’s own input during the event. The upstream power supply, terminals and cable run can all affect the voltage seen by the unit.
Before removal, photograph the EN/UH wiring, alarm relay terminals and jumper positions. Use that record to check which alarms should shut down the rack after the replacement.
When all three fan LEDs flash together, start with the filter and air path. Siemens specifies about six seconds for fan fault indication to appear after a reset. Allow for that delay before reading the LEDs again.
For a used power supply, ask for a loaded 5.1 V reading in a compatible rack, along with fan and alarm test results. For a planned swap, record the program backup and battery status on the work order.
OtomasyonAVM resources and PDFs
+ SIMATIC S5 power supplies and Siemens S5 PLC overview.
+ OtomasyonAVM shared SIMATIC S5 PDF archive.
Related topics
+ 6ES5 955-3NC42 power supply · 24 V DC input and 18 A main rail.
+ 6ES5 955-3LF42 power supply · 120/230 V AC input and 40 A main rail.
+ 6ES5 188-3UA32 central controller · 18 A rack configuration with a 24 V DC input.
To offer a 955-3NF42 for sale, email the nameplate photo, quantity and test status to otomasyonavm@gmail.com.
Navigation
+ S5 power supplies · S5 racks · SIMATIC S5 · Used Siemens equipment
External references
+ Siemens SIMATIC S5-135U/155U System Manual (PDF) · C79000-G8576-C199-07, rack compatibility p. 4-19, troubleshooting pp. 4-36–4-39 and electrical ratings pp. 4-54–4-56.
+ UL E143289 component listing (PDF) · Includes 6ES5955-3NF42.