6ES5 955-3LF42
Siemens 6ES5 955-3LF42 SIMATIC S5 power supply, 120/230 V AC input, 5.1 V DC / 40 A output
The Siemens 6ES5 955-3LF42 is a fan-cooled 955 rack power supply for SIMATIC S5-135U/155U systems. It has a selectable 120 or 230 V AC input and supplies 5.1 V DC at 40 A to the rack backplane. Siemens lists this exact order number for the 6ES5 188-3UA22 central controller and the 6ES5 185-3UA33 expansion unit.
The supply powers the CPU and module electronics in the S5 rack. The 6ES5 955-3NF42 has the same main output rating but takes 24 V DC. The 6ES5 955-3LC42 offers the same AC input selections and has an 18 A main output.
AC input selection and current draw
The input range is 93–132 V AC in the 120 V position and 187–264 V AC in the 230 V position. The nominal frequency is 50/60 Hz, with an allowable range of 47–63 Hz. At rated load, input current is 4.5 A RMS at 120 V and 2.6 A RMS at 230 V. Siemens specifies a peak inrush current of 25 A for 2 ms.
When comparing the 3LF42 with the 3LF12 or the 3LF41, check the rack order number, voltage selector and front-panel connections. The front-panel Power switch controls standby. Isolate the incoming AC supply before removing the unit or working on its connections.
5.1 V, 15 V and 24 V outputs
The main output is rated at 5.1 V DC and 40 A. The 15 V DC / 2 A output is regulated. The 24 V DC / 2.8 A rating is the combined limit for the 24 V current drawn at X2 and the front terminals. Include CP 535 and other S5 communications modules in the rack inventory. During fault finding, record the state of each of the 5 V, 15 V and 24 V indicators.
Matching the central controller and expansion rack
The 6ES5 188-3UA12 central controller and the 6ES5 183-3UA13 and 6ES5 185-3UA11 expansion units are examples of 18 A AC-fed configurations. If several racks are linked through S5 interface modules, identify the rack where the fault began and read its label.
Record the processor code, such as CPU 928 or CPU 948, in the service log. Match the replacement supply using the full central controller order number and the label on the installed supply.
Fan warning, fan alarm and external voltage monitoring
In the three-fan arrangement, the supply switches off a failed fan and increases the speed of the remaining two. A failure of two fans or inadequate airflow can trigger Fan Alarm. With EN present and the F-R jumper closed, the Siemens fault table shows that this condition shuts down the power supply outputs. Check the front-panel LEDs alongside the cabinet relay signals to distinguish a warning from an alarm.
The Voltage Monitor input watches the cabinet’s external 24 V DC load supply. If Voltage low is lit, trace that circuit using the S5 wiring and connector layout. If several S5 digital outputs drop together, record the BASP status as part of the fault diagnosis.
Editor’s note
Read the whole order number. The 6ES5 955-3LF44 is also listed in the 40 A class. When sourcing a spare, keep photos of the supply label, rack label and front panel together.
Record the LEDs before resetting. A single illuminated fan LED and several flashing fan LEDs point to different fault conditions. Note the Alarm indicator and the condition of the filter drawer if one is installed.
Read the front-panel test point on its own scale. The socket marked 3 V = 40 A represents main output current. A 3 V reading at that socket corresponds to a 40 A load on the 5.1 V rail.
Check the program backup before removal. Confirm that the STEP 5 backup is current. If the S5 memory configuration relies on battery-backed RAM, check the MB low and RB low indicators as well.
Ask for test results under load. When comparing used PLC power supplies, ask which AC input setting was used, what load was applied to the 5.1 V rail and whether any fan warning appeared.
OtomasyonAVM resources and PDFs
About Siemens SIMATIC S5 PLCs · SIMATIC S5 racks
OtomasyonAVM SIMATIC S5 PDF archive — manuals published for the S5 family.
Related topics
6ES5 955-3LF41 · 6ES5 955-3LF44 · 6ES5 955-3NF42 with 24 V DC input
Browse this family
Siemens S5 PLCs → SIMATIC S5 → S5 power supplies
External references
Siemens S5-135U/155U System Manual — 3LF42 rack assignments, section 4.3.1
Siemens S5-135U/155U System Manual — fan warning and alarm behaviour, section 4.3.3
Siemens S5-135U/155U System Manual — 3LF42 input and output ratings, section 4.3.6