6ES5 466-8MC11
6ES5 466-8MC11 — 4-Channel 0–10 V Analog Input Module
The Siemens 6ES5 466-8MC11 is a four-channel 0–10 V analog voltage input module for S5-90U, S5-95U, S5-100U, ET 100U and ET 200U systems in the SIMATIC S5 range. It has no galvanic isolation. Each channel supplies an 8-bit value in a single byte, unlike many other S5 analog modules that use a word for each measurement.
It reads voltage signals from 0–10 V sensors, transducers and compatible equipment. The PLC program converts these readings into pressure, level, position or other engineering units. In analog signal applications, match the sensor's output range to the module's input range.
Measurement specifications and power
Input resistance is 100 kΩ, and conversion uses successive approximation. Basic error limits are ±0.4%; operational error limits over 0–60 °C are ±0.6%. Siemens specifies an A/D conversion time of 100 µs and a separate encoding time of 5 ms per input. The 100 µs figure must not be treated as the complete measurement update time seen by the PLC.
The module draws a typical 100 mA from the system's +9 V supply, with approximately 0.9 W power loss. It requires no external L+ supply. Power the sensor separately as its own connection requirements dictate. The specified maximum shielded cable length is 200 m; dependable analog measurement also depends on wiring and reference connections.
Input terminal connections
For two-wire voltage sensing, use channel 0: 3 (+), 4 (−); channel 1: 5 (+), 6 (−); channel 2: 7 (+), 8 (−); channel 3: 9 (+), 10 (−). Terminals 1 and 2 are shown unconnected in this module's diagram. When selecting S5 cables and connection accessories, check both the module markings and the bus unit's terminal numbering.
A 4–20 mA signal must not be connected directly as a 0–10 V input. Any required conversion needs a suitable circuit with the correct loading, reference and measurement range. The difference between voltage and current signals cannot be resolved simply by changing a software scale.
8-bit values and scaling
The raw reading ranges from 0 to 255. Siemens' table gives 0 → 0 V, 128 → 5 V and 255 → approximately 9.961 V. One count represents approximately 39.06 mV, giving the nominal calculation U ≈ raw value × 10 / 256. A scale of 256 units does not mean that a byte can report a value of 256.
In the PLC program, treating two adjacent input bytes as one channel's measurement combines readings from two channels. Do not process this module's raw data directly as a 464-series analog word or apply the 0–27648 scale used by other PLC families.
STEP 5 addressing and FB250
The S5-100U manual assigns the four channel bytes to IB64–IB67 in slot 0 and IB72–IB75 in slot 1. German instruction notation uses EB instead of IB. These examples apply to the S5-100U; check the relevant system's address table for other CPUs and remote I/O arrangements.
Using FB250 requires preprocessing. Siemens' READ 466 / READ AI examples separate each channel byte, shift it left by six bits and place it in the word format expected by the block. The module provides no overrange or sensor wire-break indication; PLC troubleshooting must account for that limitation.
Editor's note
The 466-8MC11 and 464-8MC11 are different modules. The 6ES5 464-8MC11 accepts ±10 V and has galvanic isolation. Compare the data representation and program as well as the signal range before considering a replacement.
Without galvanic isolation, the sensor's reference must be assessed together with the PLC reference. Distinguish external sensor power from the module's bus supply. Checking the PLC power supply cannot replace a measurement at the sensor terminals.
Test inputs of 0, 2.5, 5 and 7.5 V should produce readings close to 0, 64, 128 and 192. Check the terminal voltage first, then monitor the corresponding byte to separate wiring, channel-address and scaling problems.
A zero reading alone does not establish a broken wire. The process value may be zero, sensor power may be missing, or the program may be monitoring the wrong byte. Check a suspect channel with a known voltage source.
Translate the approximately 39 mV step into the process units that matter. With a 0–10 bar sensor, one count represents approximately 0.039 bar. Displaying more decimal places does not improve the module's measurement resolution.
OtomasyonAVM information and PDF pages
Our introduction to Siemens S5 PLCs covers the platform. The OtomasyonAVM S5 PDF archive page also lists the S5-100U manual. In that English manual, printed pages 11-16–11-18 cover data processing, while 14-54–14-55 contain the module wiring and specifications.
Related topics
Other input options include the 6ES5 464-8MB11 for ±1 V, 6ES5 464-8MD11 for ±20 mA and 6ES5 464-8ME11 for 4–20 mA. Their signal types and data representations must be checked separately.
The 6ES5 464-8MF11 handles Pt100/±500 mV measurement. The 6ES5 470-8MA12 is a two-channel ±10 V output module; distinguish a card that reads measurements from one that generates control signals.
Further navigation
SIMATIC S5 CPUs · S5 module pages · S5 digital input modules · S5 digital output modules
External references
Siemens S5-100U System Manual — EWA 4NEB 812 6120-02b, English PDF. Table 11-13 and the following FB250 examples are on physical PDF pages 286–288. Wiring and specifications are on PDF pages 404–405.
Siemens 6ES5466-8MC11 data sheet — German, third-party archive copy. Confirms the exact order number, supported systems and four 0–10 V inputs.