6ES5 464-8MC11

Siemens 6ES5 464-8MC11 — 4 × ±10 V Analog Input Module

The Siemens 6ES5 464-8MC11 is a four-channel ±10 V analog voltage input module for SIMATIC S5 systems. It converts voltage signals into digital measurements in S5-90U, S5-95U, S5-100U, ET 100U and ET 200U installations. This S5 analog module has an input resistance of 50 kΩ and uses a 12-bit plus sign digital representation.

The module passes a field analog signal to the PLC program. Sensors with 0–10 V outputs can also be read within the nominal range when their output and reference connections are suitable; they use the positive half of the bipolar measuring range. Bipolar feedback uses the −10 V to +10 V range.

Input range and module selection

The suffix matters: the 6ES5 464-8MB11 measures ±1 V, while the 6ES5 466-8MC11 is a different module for 0–10 V inputs. A similar housing does not establish identical wiring or digital value representation.

Keep voltage and current signals separate when selecting the input hardware. Consider the 6ES5 464-8MD11 for ±20 mA or the 6ES5 464-8ME11 for 4–20 mA. Direct Pt100 or ±500 mV measurements require different hardware, such as the 6ES5 464-8MF11.

Terminals, power supply and isolation

Channel 0: 3 (+), 4 (−); channel 1: 5 (+), 6 (−); channel 2: 7 (+), 8 (−); channel 3: 9 (+), 10 (−). Connect each voltage signal to its positive and negative measuring terminals. Check the terminal numbering on the bus unit when inspecting S5 cables and connectors.

The electronics use the system bus +9 V supply; this module does not require an external L+ supply. Any power required by the sensor must be considered separately. Include the S5 power supply and bus unit in the installation checks.

The inputs are galvanically isolated from the grounding point, but not from one another. Check reference potentials and the grounding arrangement before connecting signals from separate sources. An isolated module does not provide four individually isolated channels.

Channel selection and 50/60 Hz setting

The front operating mode switches select one, two or four channels: Ch0, Ch0–Ch1 or Ch0–Ch3 respectively. Review the S5 module arrangement and program addresses together with the selected channel count.

Select 50 or 60 Hz to match the supply frequency. Integration time is 20 ms at 50 Hz or approximately 16.6 ms at 60 Hz. This setting affects noise immunity. The module-specific manual shows switch 4 in the OFF position.

Scaling and measurement updates

The measurement units are −2048 at −10 V, 0 at 0 V, +1024 at +5 V and +2048 at +10 V. Values are transmitted in left-justified two’s complement format. In PLC programming, distinguish these measurement units from the directly read 16-bit raw word.

With the lower status bits clear, the raw words are C000h at −10 V, 0000h at 0 V, 2000h at +5 V and 4000h at +10 V. Account for the sign and overflow information when scaling. Do not transfer a familiar S7 input scale directly to this module.

At nominal full scale, encoding time per input is up to 60 ms at 50 Hz or 50 ms at 60 Hz. This is separate from the PLC scan time. Consider the measurement update when assessing closed-loop feedback, and distinguish the input function from that of a 6ES5 470-8MA12 analog output module.

Fault finding and used-module checks

This model has no sensor wire-break detection. Before proceeding with PLC debugging for a zero or unstable reading, measure whether the expected signal is actually present at the module terminals. When assessing a used unit, check the full label, switch settings, bus-unit connections and test results for all four channels.

Editor’s note

Take a moment to photograph the old module’s label and switch settings before replacing it. Matching the order number is only part of the job; a different channel setting can leave you troubleshooting a perfectly serviceable replacement.

If a reading disappears, give the wiring a fair check before condemning the card. Measure between the positive and negative terminals of the affected channel. A good signal at the sensor may still be lost through a loose terminal or broken conductor.

If bench testing is possible, apply 0 V, +5 V and −5 V from a known source and compare all four channels in turn. A single correct reading on one channel is a limited check; testing both polarities gives a more useful picture.

Keep the isolation arrangement in mind: the channels are not isolated from one another. Check signal references before bringing connections from different machines onto one card. Replacing the module may leave a reference-potential problem exactly where it was.

A zero on the screen does not prove that the sensor is sending zero: this module does not report a broken sensor wire. Review the S5 system layout, the measured field voltage and the program’s raw value together. A steady sequence of checks often saves a serviceable part.

OtomasyonAVM resources and PDFs

+ About Siemens S5 PLCs and the S5 analog module pages provide starting points for system and module selection.

+ Browse the OtomasyonAVM S5 PDF archive for system manuals. For the 6ES5 464-8MC11, relevant sections are 11-7, 11-12 and 14-44–14-45 in the S5-100U manual and 15-62–15-65 in the S5-90U/S5-95U manual. The manufacturer documents linked below are in English.

Related topics

+ 6ES5 464-8MB11 — ±1 V analog input · 6ES5 464-8MD11 — ±20 mA analog input.

+ 6ES5 464-8ME11 — 4–20 mA analog input · 6ES5 466-8MC11 — 0–10 V analog input.

Browse SIMATIC S5

+ S5 analog modules · S5 90/110 module group · SIMATIC S5 systems.

+ Siemens S5 main page · Used Siemens automation equipment.

Siemens and external references

+ Siemens S5-100U System Manual — EWA 4NEB 812 6120-02b, English: wiring, mode selection, value representation and the exact-model specifications.

+ Siemens S5-90U/S5-95U System Manual — EWA 4NEB 812 6115-02b, English: module description and measurement scaling for the 6ES5 464-8MC11.

+ Siemens ET 100U Manual — EWA 4NEB 812 6040-02a, English: module wiring and specifications on printed pages 2-42–2-43.

+ Siemens ET 200U Manual — EWA 4NEB 812 6087-02b, English: wiring, value representation and module data on printed pages 7-5, 7-18 and 8-47–8-48.