6ES5 461-8MA11

Siemens 6ES5 461-8MA11 – Two-Channel Analog Threshold Comparator Module

Siemens 6ES5 461-8MA11 is a two-channel, galvanically isolated comparator module with selectable current or voltage inputs. It is documented in the S5-100U and ET 200U manuals. It compares each analog signal with a front-panel threshold. Reaching that threshold lights the channel's green LED and sends a status bit to the Siemens S5 PLC.

The PLC receives one bit per channel. Threshold states are read through digital input addresses. Applications requiring continuous numerical measurements, scaling or trend recording need a suitable S5 analog input module. This distinction matters when selecting spares within the Siemens S5 system.

Input ranges and channel selection

Voltage: 0.5–10 V DC, with 47 kΩ input resistance. Current: 0.5–20 mA in the technical tables, with 500 Ω input resistance. Each channel has a U / 0 / I selector: U selects voltage, I selects current, and 0 disables the comparator and reports a zero to the PLC. For 0–10 V and 4–20 mA signals, check the transmitter output against the selected mode.

Documentation difference: the S5-100U manual's section 15.1 heading and front-panel illustration show 1–20 mA, while its technical table states 0.5–20 mA. Both the heading and table in ET 200U section 9.1 state 0.5–20 mA. For thresholds near the lower limit, check the actual module marking and verify operation with a calibrator.

When connecting a 4–20 mA analog sensor, allow for the input burden: 20 mA × 500 Ω = 10 V across the module input. The transmitter supply, permitted load and cable losses must support that operating point.

Threshold adjustment, hysteresis and response

Front-panel potentiometers set the thresholds. Siemens specifies ±10% setting error, ±2% reproducibility and 10% hysteresis. These describe different characteristics; reproducibility must not be treated as measurement accuracy. The voltage input's typical 5 ms inherent delay is only part of the application's response time; CPU and communication delays also contribute.

Connections and supply

The S5-100U diagram shows channel 0 on terminals 3 (+) and 4 (−), and channel 1 on terminals 9 (+) and 10 (−). The channel selector determines current or voltage operation. Remove the module or disconnect the measuring circuit before changing the function. Unused inputs may remain open. Check the cables and connections and the installation's grounding arrangement.

The electronics draw typically 35 mA from the CPU/bus +9 V rail. Typical power loss is 0.3 W and approximate weight is 200 g. This internal supply specification does not identify a field supply output for a transmitter.

Addressing and STEP 5 example

In the S5-100U, the module is addressed like a two-channel digital input: channel 0 = I x.0 and channel 1 = I x.1, where x is the slot address. Siemens' slot 4 example reads I 4.1. The PLC program uses A I 4.1 followed by = Q 5.1 to operate a digital output. Q 5.1 is a separate application output address, not a relay contact on the 461.

With ET 200U, the input byte's location depends on the station configuration; the slot 4 example is not a universal installation address. Before replacement, check the complete order numbers and project for the S5 CPU, CPU 90U family, compact S5 modules and additional modules in the existing installation.

Comparison with numerical analog I/O

6ES5 464-8MA11, 6ES5 464-8MB11 and 6ES5 464-8ME11 are different analog input versions providing numerical values. Select their input ranges and system compatibility from their own documentation. 6ES5 470-8MA11 is an analog output module. None should be selected as a direct replacement solely because it belongs to the S5 analog I/O family.

Editor's note

Take a little time with the threshold adjustment. Increase the calibrator signal slowly, then reduce it, and record each channel's switching and release points. The dial alone does not establish the actual trip point.

Watch the PLC input bit while checking the LED. During fault finding, follow both the status reported by the module and the logic that uses it.

Disconnect the measuring circuit before moving the U/I selector. Select the correct mode, then test under controlled conditions. Photograph the old module's selector and potentiometer positions before removal.

If a current threshold cannot be reached, check the transmitter's available load capacity and supply voltage before condemning the module. Include other devices connected in series in the loop calculation.

If the state jumps while adjusting the potentiometer, or the same position produces inconsistent results, record that behaviour. Test several thresholds in both directions rather than accepting a single illuminated LED.

For used Siemens equipment, obtain a clear 461-8MA11 label photograph and a test record covering both channels and the U/I modes used. Verify the adjustment and the corresponding PLC bit together.

OtomasyonAVM resources and PDFs

Browse About Siemens S5 PLC, analog modules and S5 additional modules for related equipment. The S5-90U PDF archive provides family documentation. Detailed technical descriptions of this comparator are in the manufacturer's S5-100U and ET 200U manuals below.

Related topics

+ 6ES5 464-8MA11: analog input module.

+ 6ES5 464-8MB11: analog input version with a different input range.

+ 6ES5 464-8ME11: another version in the analog input family.

+ 6ES5 470-8MA11: analog output module.

Browse S5 equipment

Siemens S5 PLC · S5 CPUs · Digital inputs · Digital outputs · Cables · Used Siemens equipment

Manufacturer documents and external references

+ Siemens S5-100U System Manual – EWA 4NEB 812 6120-02b: section 15.1, printed pages 15-1–15-3; PDF pages 413–415. Specifications, wiring, function selection and addressing example.

+ Siemens ET 200U Distributed I/O Station – EWA 4NEB 812 6087-02b: section 9.1, printed pages 9-2–9-4; PDF pages 295–297. Comparator specifications and operation.