Delta ASDA-MS

Delta ASDA-MS Robot Controller with Integrated Servo Drives

Delta ASDA-MS combines a robot controller and four built-in servo drive channels in one unit for industrial robotics. Supported versions and configurations can add two external axes over DMCNET. The application’s mechanical layout determines the axis control and robot motion program.

ASDA-MS catalogue and model tables

Delta ASDA-MS Series Catalogue (PDF, English) · 13 April 2021 · 36 pages. See printed page 14 for ordering codes, pages 18–19 for motor combinations and specifications, and page 20 for the port layout. The Delta Servo Manuals archive covers the other series.

Robot type, motion path and axis count

ASDA-MS supports point-to-point (PTP) motion and linear and circular interpolation. Check the catalogue’s mechanism table for the F, FR, C and V versions. For SCARA, Delta or articulated robots, match the robot kinematics and multi-axis synchronization to the project’s axis layout.

Power class and motor matching

The catalogue lists 400 W for ASD-MS-0421, 750 W for ASD-MS-0721 and 1,000 W for ASD-MS-1023. When matching motors and drives, check the approved servo motor combination for J1–J4, the supply phase and the enclosure temperature.

For Delta ECMA motors, verify the complete motor code, encoder type and feedback cable together. If the mechanism changes, recalculate load inertia and gear ratio. On an axis with a planetary gearbox, backlash and transmission ratio also affect the axis’s mechanical response.

DRAS, communications and commissioning

DRAS supports project development with IEC 61131-3 languages, PLCopen motion blocks and Delta Robot Language (DRL). The catalogue lists Modbus TCP over Ethernet, RS-232/RS-485 for serial communication and DMCNET for external motion units. When planning supervisory control for the cell, define which tasks belong to the PLC, operator panel and robot controller.

During commissioning, verify direction and home position first. Then compare commanded and actual values in motion and position control. If speed fluctuates or current spikes during a move, examine the speed loop and current loop data separately.

Editor’s note

Ask for the nameplate and the project together. On a used unit, record the power code, full suffix and firmware version. Check that the DRAS project uses the same robot mechanism, axis count and I/O layout. Back up the project and parameters before replacement.

Check the 1,000 W model axis by axis. The ASD-MS-1023 table lists continuous output current of 7.3 A RMS for J1/J2 and 5.1 A RMS for J3/J4. Compare each motor nameplate with its assigned axis. Record the physical J1–J4 mapping, especially if the controller, motors or cables have been replaced.

Record when the encoder alarm appears. If it repeats at a specific cable-chain position, inspect the connector and the cable section that flexes. If it repeats at startup, start with the motor code, encoder type and axis assignment. Use the fault history to assess signal noise and shielding.

Run the first test one axis at a time. Under safe test conditions, verify direction, limit inputs and holding-brake operation at low speed. After homing, compare actual axis positions with the reference in the backed-up project before starting the robot program. If axes work individually and fault during coordinated motion, check the coordinate and mechanism settings.

Record any alarm that occurs only during deceleration. If the DC bus reports overvoltage, review the deceleration profile, load inertia and regenerative braking arrangement together. Confirm external resistor connections against the documentation for the exact hardware suffix.

Inspect the mechanics when an axis vibrates. During maintenance, check for a loose coupling, binding and bearing noise. Record whether the vibration repeats at the same mechanical position. Back up the current settings before running auto-tune or changing servo loop gains.

Related Delta equipment

See the dedicated series pages for Delta ASDA-M and Delta ASDA-A2. For cell planning, also see Delta AH motion controllers, Delta PLC and Delta DOP-100 panels.

Browse · Delta servo drives · Delta Automation

Manufacturer reference

Original Delta ASDA-MS Series Catalogue