Delta ASDA-M
Delta ASDA-M Three-Axis Servo Drive Series
The Delta ASDA-M is a servo drive series that controls three AC servo motors in one unit. Its axis synchronisation suits gantries with two motors moving a shared bridge and industrial applications where a tool moves along several axes at once.
Drive codes and communication options
The ASD-M-0721-□ supports up to 750 W per axis and the ASD-M-1521-□ supports up to 1.5 kW per axis. Both are 220 V class drives. Use the specification table for the complete model code to check the supply phase, input current and permitted motor combination across the three axes.
In Delta’s model table, the -M variant supports CANopen and electronic cam (E-CAM). The -F and -R variants support DMCNET and E-CAM. The -L is the basic variant without those three features. Identify the commands sent by the machine’s PLC or motion controller and compare the complete codes of the installed and replacement drives. For DMCNET equipment, see the Delta AH20MC-5A motion module and Delta HMC07 controllers. Confirm compatibility using the controller model, drive variant and firmware version.
Gantry control, positioning and motor selection
ASDA-M motion functions include linear, circular and helical interpolation. Where two motors move the same bridge, check both home references and mechanical squareness as part of position control. Comparing the speed and torque on both sides during a full cycle can show whether one side consistently carries more load.
Delta’s matching table lists ECMA-C△0807□S for the ASD-M-0721-□ and ECMA-E△1315□S for the ASD-M-1521-□ as examples. When matching a motor and drive, use the complete Delta ECMA motor code for each axis. The △ position identifies the encoder type. Shaft, brake and seal options also depend on the motor code. Match the power and feedback leads to the full motor code using the Delta servo cable tables.
For a new axis, size the motor for the load inertia, speed, peak torque and cycle time. Backlash, coupling compliance and homing repeatability also affect positioning accuracy.
ASDA-Soft and commissioning
Connect through CN4 USB with a compatible version of Delta ASDA-Soft to read parameters, make a backup and monitor axis behaviour. Save the original configuration before you change the drive settings. After auto-tuning, observe acceleration and stopping under the actual load. If vibration persists, investigate mechanical resonance and electrical noise on the feedback line separately.
On machines with frequent acceleration and deceleration on all three axes, monitor motor temperature and cabinet ventilation during a normal cycle. If a DC bus overvoltage alarm appears during deceleration, inspect the regenerative braking circuit and the deceleration ramp. On a vertical axis, check the motor holding brake separately.
Editor’s Note
Start with the nameplates. Ask for a photo of the full drive code and the labels on all three motors. A one-letter change can cost you the communication interface or electronic cam function the machine uses.
Ask to see all three axes run on a used drive. With a compatible motor, have the seller show forward and reverse motion, a changing position feedback value and the alarm status for each channel. The front-panel SEL key selects X, Y or Z.
Record the axis assignments before removal. Mark each pair of motor power and encoder plugs with its axis name. In the ASDA-Soft backup, capture the working parameters, programmed position registers, gantry offsets and any network settings in use.
Check gantry squareness first. Inspect both home sensors, the alignment of the bridge and the saved offset. Confirm the references on both sides agree with the machine setup before commanding the bridge to move as a group.
Record which axis faults and when. An alarm during homing calls for different checks from one during rapid acceleration or deceleration. Record the alarm code, the active axis and the stage of motion where it occurred.
Inspect cables across the full travel. If a fault comes back at the same bridge position, check the cable carrier and the points where the encoder lead flexes. Keeping separate notes on connectors, cables and motors during servo motor maintenance makes recurring faults easier to trace.
Delta ASDA-M PDF downloads
ASDA-M User Manual – PDF, English · Connections, parameters, operating modes and alarms.
ASDA-M Technical Catalogue – PDF, English · Drive and motor combinations, dimensions and accessories.
For documents on other series, visit the Delta Servo Manuals archive.
Related topics and Delta equipment
Servo system FAQs · Delta servo communication units · Delta servo drive series
For documentation on other drives in the machine, see Delta ASDA-A2, Delta ASDA-A2R, Delta ASDA-MS and Delta ASDA-S.
Manufacturer reference · Delta Electronics ASDA-M technical catalogue