Delta IFD6530
Delta IFD6530 — USB / RS-485 Communication Converter
Delta IFD6530 is an interface converter connecting a computer’s USB port to RS-485 equipment. Delta specifically describes its use with C2000 drives and its +9 V auxiliary supply. It belongs to the Delta DVP interfaces range; consult the C2000 manuals when selecting the connection and application.
Main technical specifications
| Item | Value |
|---|---|
| Power supply | USB; no external supply required |
| Power consumption | 1.5 W |
| Isolation voltage | 2500 V DC |
| Serial data-rate range | 75–115200 bit/s |
| Communication | RS-485 half-duplex; automatic direction switching |
| Connectors | Male USB Type-A / RJ45 |
| USB standard | USB 2.0 |
| RS-485 cable limit in the manual | 100 m maximum |
Assess cable length together with data rate, topology and electrical noise. A documented upper limit does not guarantee identical results in every installation. Select suitable DVP communication cables and network connectors according to the electrical connection requirements.
RJ45 pinout and differences from IFD6500
| RJ45 pin | IFD6530 | IFD6500 |
|---|---|---|
| 1 / 2 / 7 | Reserved | Reserved |
| 3 | GND | Reserved |
| 4 | SG− | SG+ |
| 5 | SG+ | SG− |
| 6 | GND | Reserved |
| 8 | +9 V | Reserved |
Do not assume the same RJ45 cable is directly interchangeable between IFD6500 and IFD6530. Compare the table with the target equipment’s port. Confusing the front and rear connector views can reverse the apparent pin order.
Use the +9 V auxiliary pin only for a suitable accessory connection; it does not supply the drive’s main power. Do not connect arbitrary loads or apply external voltage to this pin. The RJ45 socket carries RS-485 and auxiliary signals and must not be used as an Ethernet connection.
USB driver and connection preparation
Delta’s installation sequence is to extract the USB driver package first, then connect IFD6530 and complete installation. Green indicates power; flashing orange indicates data transmission. Check operating-system support against the driver package used.
After installation, check the operating system’s device status and the communication port selected in the application. Match the target address, baud rate, parity, data/stop bits and ASCII/RTU mode where applicable. When choosing between this converter and DVP programming cables, use the PLC’s actual port requirements; a USB connector alone does not establish programming compatibility.
For DVP PLC applications, evaluate ISPSoft, WPLSoft and COMMGR settings against the supported PLC and software version. An incorrect port or serial format can prevent communication even when the physical IFD6530 connection is correct.
C2000 keypad and TPEditor use
Delta describes creating a custom C2000 main screen with TPEditor and IFD6530. For KPC-CC01 programming, the C2000 manual also specifies a CBC-KxFT extension cable. Treat keypad screen editing and changing the drive’s motor parameters as separate applications.
A TPNO warning can appear when the KeypadTP Editor function is used with an unsupported target or drive series. Delta describes returning the main screen to Default in that situation; User Define can be selected after preparing the appropriate custom screen. The warning alone does not establish an IFD6530 fault.
Comparison with other IFD interfaces
IFD6503 provides USB/CAN connectivity. IFD8500-A converts between RS-232 and RS-422/485, while IFD8510-A is a line repeater. IFD8520 provides an addressable serial-interface function. These products serve different purposes from IFD6530.
For network protocol conversion, IFD9502 DeviceNet and IFD9503 CANopen are separate products. Select IFD6530 according to the connection needed between a computer and a suitable RS-485 port.
Editor’s Note
Do not substitute IFD6500 and IFD6530 based on appearance. Check the model label and RJ45 pinout first. A cable that worked with one converter may not perform the same task with the other.
For an initial used-unit test, connect directly to the computer with a short, known-good cable. Remove USB hubs and long extensions from the first test. If the device is not recognized, check the USB port, driver installation and physical cable condition in sequence.
A flashing orange LED alone does not prove a correct reply from the target. Read a known register and compare the result with the equipment display. Perform any write test only on a safe test parameter after recording its previous value.
When measuring the +9 V pin, select the correct GND reference and avoid bridging adjacent contacts with the probe. Finding this voltage does not prove that the data interface works. Record the power check and actual communication test separately.
Do not classify a unit as reliable for continuous service if its RJ45 latch is broken, contacts are corroded or moving the cable interrupts communication. Check mechanical stability first. Matching connector shapes do not establish compatibility between CAN, Ethernet and RS-485 cables.
Back up existing parameters and communication settings before working on an operating drive. Begin with identification and reading values. For used equipment, request a read test with suitable equipment and the connection details rather than an LED photograph alone.
PDF, software and related topics
Use the Delta PLC accessories PDF and software files page for installation documentation and software links. Further sources are available under Delta user manuals and Delta PLC and HMI manuals.
Navigation: IFD6530 main page · Delta PLC accessories · Delta PLC models · Used Delta products
External references
Delta IFD6500 / IFD6530 Instruction Sheet — 2021-10-28 · Delta IFD Series — Functions and Applications · Delta C2000 — TPEditor / IFD6530 / TPNO · Delta C2000 Manual — KPC-CC01 / IFD6530 (RU)