6ES5 316-8FA12
Siemens 6ES5 316-8FA12 — IM 316F Interface Module
6ES5 316-8FA12 is an IM 316F interface module that extends the I/O bus between DIN-rail tiers in SIMATIC S5 systems. It provides enhanced EMC protection and supports arrangements with up to four tiers including the main tier.
Siemens ST 50 lists S5-90U, S5-95U/F and the S5-100U range as applications. For S5-95F, IM 316F is required within this interface group. S5-95F systems such as 095-8FB01 also require the specific arrangement rules for subunits A and B.
Tier expansion and cable selection
One interface is needed on each DIN-rail tier, allowing up to three expansion tiers in addition to the main tier. For S5-95F, the limit is eight bus units per A/B subunit in total; do not interpret this as eight on every tier when planning expansion modules.
Two interfaces are joined by a 712 connecting cable: 6ES5 712-8AF00 — 0.5 m, 6ES5 712-8BC50 — 2.5 m, 712-8BF00 — 5 m or 712-8CB00 — 10 m. The catalogue specifies 10 m maximum between tiers.
The ribbon cable connects to the last bus unit. The inter-tier cable runs from OUT on the preceding tier to IN on the next. Check the exact codes of suitable S5-95F bus units, including 700-8FA11 and 700-8MA22.
S5-95F and electrical limits
IM 316F carries the bus connection; it does not perform the functions of the 431-8FA11 digital input, 450-8FA11 digital output or 464-8MG11 analogue input module. Assess each I/O module against its own wiring and parameter rules for the safety application.
The S5-95F manual specifies 1 A maximum supplied to the expansion unit. Check the power-supply arrangement and module loads together. Dimensions are 45.4 × 135 × 39 mm; weight is approximately 120 g.
The permitted potential difference between the DIN rail and the CPU central grounding point is ±1 V. Rails in separate cabinets require a common reference. For EMC, unused Sub-D connections must be covered with the 6ES5 750-2AA21 empty connector.
Similar codes and functional checks
The catalogue specifically excludes the standard 6ES5 316-8MA12 from S5-95F use. Other S5 communications/interface parts, such as 318-3UA11, must be assessed by their own function; nearby order numbers do not establish interchangeability.
During fault investigation, examine the label, connecting cable, ribbon connection and rail grounding together. Observe the actual input/output conditions during testing and include validation of the S5-95F safety functions in the maintenance plan.
Editor’s note
Take a moment to read the 8FA12 suffix carefully. Particularly on an S5-95F, a similar-looking 8MA12 should not be fitted on appearance alone; that distinction matters.
If a tier disappears from the system, do not condemn the interface straight away. Check the cable, OUT–IN direction and ribbon connection in order. One tired contact can cause a long search in an old panel.
When linking cabinets, give grounding attention from the start. Check the rails and connections before spending time swapping parts that may already be working properly.
Keep the unused-connector covers with the equipment. They have a purpose in the EMC arrangement, so put them back carefully after maintenance.
For a used module, ask for clear photographs of the label, contacts, ribbon cable and rail latch. Where possible, see it working on suitable equipment; a tidy case alone does not prove that the interface works.
OtomasyonAVM resources and PDFs
+ OtomasyonAVM S5 PDF archive · About Siemens S5 PLCs. Refer to S5-95F manual sections 5.2 and A.1.5 and ST 50, page 2/76 for this module.
Related topics
+ 712-8AF00 connecting cable · 712-8BC50 connecting cable · 700-8FA11 bus unit · 700-8MA22 bus unit.
Browse SIMATIC S5
+ S5 interface modules · S5 cables · SIMATIC S5 · Siemens second-hand equipment.