6ES5 436-7LA11
Siemens 6ES5 436-7LA11 — 16-Channel, 230 V AC/DC Digital Input Module
6ES5 436-7LA11 is a 16-channel, 230 V UC (AC/DC) digital input module for Siemens SIMATIC S5 S5-115U systems. This model in the S5 digital input range has four optocoupler-isolated groups of four inputs. The specified frequency range for AC signals is 47–63 Hz.
The board transfers status signals from field contacts at the appropriate voltage to the SIMATIC S5 CPU. Check the complete order code, front wiring and existing rack arrangement together. Approximate weight is 0.7 kg; distinguish its inputs from those of a 24 V DC input board.
Input thresholds and current
Logic “0” is specified at 0–70 V and logic “1” at 170–264 V. Do not use the region between those ranges as a guaranteed logic state. Typical logic-1 input current is 15 mA at 50 Hz AC and 2.2 mA for DC. Assess a sensor’s output voltage and leakage current against these ratings.
Isolation and front wiring
Each four-input group is isolated. However, the manufacturer explicitly states that connecting different phases is not permitted. Follow the diagram for group returns and grounding. The manual lists the 46-pin screw-terminal 6ES5 490-7LB21 front connector; check any terminal transfer against the exact 436-7LA11 wiring diagram.
Two-wire sensor connections
The manual permits two-wire BERO proximity switches and specifies a 3 mA quiescent-current value. The sensor must have the correct voltage rating for a 230 V UC input. Two-wire construction alone does not establish compatibility.
Response times
Response times are 2–13 ms from “0” to “1” and 10–35 ms from “1” to “0”. Account for these delays when assessing short pulses. Do not assume this standard status-input module is suitable for high-speed counting or encoder pulses.
Temperature and simultaneous inputs
At L1 = 264 V, the simultaneity factor per group is 100% at 25 °C and 75% at 55 °C. Under the specified 55 °C condition, this permits at most three active inputs in each four-input group. Typical module power loss is 11 W, and consumption from the internal 5 V supply is 5 mA.
Cable length and field measurements
Maximum S5 field-cable lengths are 1000 m shielded and 600 m unshielded. Assess cable capacitance, interference and leakage voltage separately. Measure between the relevant input and its own group return; a voltage reading to earth alone is insufficient.
Addressing and fault tracing
Compare the sixteen channel addresses and terminal assignments with the PLC program. In the appropriate programming software, ensure the monitored input bit matches the field channel being measured. Record channel order and group returns before replacement.
During troubleshooting, check input voltage, status indication and program bit in sequence. If the input reads correctly but the expected output does not occur, follow the relevant logic conditions and S5 system operating state. Isolate field and system power before removing wiring or modules.
Differences from related models
The 6ES5 436-7LB11 has 16 inputs in groups of two; the 6ES5 436-7LC11 has eight individually isolated inputs. The 6ES5 435-7LA11 is rated 115 V UC, while the 6ES5 430-7LA12 uses 24 V DC inputs. Verify channel count, grouping and voltage class before considering interchangeability.
Editor’s note
Keep the 230 V UC input rating in mind from the start. A familiar status-signal function does not make this the same connection as a 24 V sensor output. Reading the label and full order code first can save a long fault search later.
If four inputs disappear together, give the board a fair check before condemning it. Inspect that group’s return, terminal tightness and field supply. Four isolated groups do not permit different phases; the manufacturer rules that out for this model.
Pay closer attention where many inputs remain active in a hot cabinet. The 75% limit at 264 V and 55 °C applies per group. Check each set of four rather than simply counting active inputs across the whole board.
If an input remains at “1” with the contact open, check sensor leakage and the voltage present on the cable. This matters particularly with two-wire sensors. Measuring against the correct group return makes the fault easier to understand.
When buying a used Siemens 436-7LA11, ask for all sixteen channels to be tested with suitable signals. Check both switching directions in every group. A few working inputs are encouraging; seeing all the groups respond is much more reassuring.
OtomasyonAVM resources and PDFs
Siemens S5-115 PDF page · S5 digital input modules · 490-7LB21 front connector. The specifications and wiring for the exact 436-7LA11 model are in the Siemens S5-115U Manual, EWA 4NEB 811 6130-02b, p. 15-28. The document is in English; the manufacturer’s link is below.
Related topics
436-7LB11 · 436-7LC11 · 435-7LA11 · 430-7LA12 · Two-wire sensors.
Navigation
S5 digital input modules · SIMATIC S5 · Siemens S5 PLC · Used Siemens.