6ES5 436-7LB11

Siemens 6ES5 436-7LB11 — 16-Channel 230 V AC/DC Digital Input Module

6ES5 436-7LB11 is a 16-channel, optocoupler-isolated digital input module for the S5-115U in the Siemens SIMATIC S5 family. Its digital inputs are arranged in eight groups of two. Rated signal voltage is 230 V UC (AC/DC), with an AC frequency range of 47–63 Hz.

It transfers 230 V contact and status signals to the PLC in SIMATIC S5 installations. The related 436-7LA11 also has 16 inputs in the 230 V class, but uses groups of four; 436-7LB11 uses groups of two. Check shared return terminals and the complete order code alongside channel count when choosing a replacement.

Signal thresholds and input current

The manual specifies 0–70 V for logic 0 and 170–264 V for logic 1. 70–170 V must not be treated as a guaranteed logic state. Typical logic-1 input current is 15 mA with 50 Hz AC or 2.2 mA with DC. These values describe current drawn by the input circuit, not a load-driving capacity.

When reading a relay or contactor state through an auxiliary contact, check the actual input voltage together with the group return connection. With interposing relays and sockets, distinguish the coil circuit from the input signal circuit.

Input delay and two-wire sensors

Response time is 2–13 ms from 0 to 1 and 10–35 ms from 1 to 0. Include the PLC scan time when assessing short pulses; this module should not be treated as a high-speed counter input.

Siemens permits suitable two-wire BERO proximity switches and specifies a 3 mA quiescent-current value. Check sensor operating voltage, leakage current and input threshold together. A standard 24 V DC sensor output does not directly drive this 230 V input to logic 1.

Isolation, phases and front connector

Isolation is provided in groups of two; each channel is not individually isolated. Siemens explicitly states that connection of different phases is not permissible for this model. Eight groups do not authorize connecting eight separate phase circuits freely.

Within the 46-pole 490 connector family, 490-7LB21 has screw terminals and 490-7LA11 uses crimp connections. When inspecting S5 cables and connections, compare connector type, channel terminals and group returns with the installed wiring diagram. The manual specifies maximum cable lengths of 1000 m shielded or 600 m unshielded; installation EMC and cable-routing requirements also apply.

Installation, addressing and temperature

Assess the suitable S5 rack, interface modules and expansion arrangement against the system manual. The 16 inputs provide two bytes of signal information; verify the start address in the PLC program against the actual installation and input/output assignment.

At 264 V input voltage, the manual gives a per-group simultaneity factor of 100% at 25 °C and 75% at 55 °C. Typical module power loss is 11 W. Assess cabinet temperature and simultaneously active inputs against this condition. During fault diagnosis, compare the actual input level with the program state and establish safe machine conditions before measurements.

Comparing related modules

436-7LC11 has eight 230 V UC inputs in individual groups; 435-7LB11 has sixteen 115 V inputs in groups of two. 430-7LA12 has thirty-two 24 V DC inputs. These modules must not be treated as interchangeable without matching voltage, channel count, grouping and wiring.

Editor’s note

Start by reading the full 436-7LB11 label. LA11 also has 16 inputs in the 230 V class, but its shared terminal arrangement differs. Take time to compare group wiring before fitting a similar-looking card.

If an input LED stays off, give the card a fair check first. Measure the signal relative to its own group return. The logic-1 range is 170–264 V; a voltage between the defined ranges cannot provide a dependable indication.

Do not distribute different phases simply because there are eight isolated groups. Siemens does not permit different-phase connections on this model. Compare the existing cabinet wiring with the diagram instead of assuming an old installation is correct.

If an input remains on with a sensor off, inspect sensor leakage and the cable. Choosing a two-wire sensor takes more than matching its voltage label; quiescent current and input threshold matter together. A careful check may save replacing a healthy card.

For a used card, check all 16 channels and the return connections of all eight groups individually. Consider cabinet temperature and simultaneous input conditions as well as a short bench test. Photograph the label, connector and address records before removal; those records help at the next maintenance visit.

OtomasyonAVM resources and PDF files

+ S5 PDF files and user manuals · About Siemens S5 PLCs. The main reference is the S5-115U Manual, EWA 4NEB 811 6130-02b, Edition 04. Exact-model specifications and wiring are on printed page 15-29 / PDF 557; front connector options are on 15-66 / PDF 594. The document is in English.

Related topics

+ 436-7LA11 groups of four · 436-7LC11 eight inputs · 435-7LB11 115 V input · 430-7LA12 24 V DC input · 490-7LB21 screw-terminal connector.

Browse SIMATIC S5

+ S5 digital input modules · S5 racks · S5 interface modules · Siemens S5 PLC · Siemens second-hand equipment.

Siemens and external references

+ Siemens S5-115U Manual — EWA 4NEB 811 6130-02b, Edition 04 / 6ES5 998-0UF23. Printed page 15-29 / PDF 557: 436-7LB11 specifications, group wiring and prohibition of different-phase connections. Printed page 15-66 / PDF 594: 490 front connector options. English.