6ES5 430-7LA12

Siemens 6ES5 430-7LA12 – 32-Channel 24 V DC Isolated Digital Input Module

Siemens 6ES5 430-7LA12 is a 32-channel, 24 V DC digital input module for SIMATIC S5 S5-115U/H/F systems. Optocoupler isolation is arranged in four groups of eight inputs. This S5 digital input module specifies −30 to +5 V for logic 0 and +13 to +30 V for logic 1.

Logic-1 input current is 8.5 mA typical. Match relay contacts and positive-switching 24 V DC field outputs to the manufacturer’s group wiring diagram. Two-wire BERO proximity switches can be used, with a specified maximum quiescent current of 1.5 mA. Measure input voltage relative to the relevant group M terminal in the Siemens S5 system.

Eight-input groups and terminal assignments

Each group of eight has its own M return. Input bytes use terminals 3–10, 15–22, 27–34 and 39–46, respectively. Their M terminals are 11, 23, 35 and 47. Label field wiring by both group and channel order.

Isolation is provided between groups; channels within each group share M. Keep protective grounding distinct from signal returns. The catalog’s 500 V insulation test rating is not a field operating voltage. Review group returns and shield connections when investigating interference.

46-pin front connector and supply calculation

The module uses a 46-pin front connector. The screw-terminal option is 6ES5 490-7LB21. Crimp versions are 490-7LA11 with contacts and 490-7LA21 with contacts supplied separately. Match the connector to the existing rack and wiring.

ST 50 specifies 5 mA maximum from the internal 5 V rail, 6.5 W typical power loss at rated operation and approximately 0.7 kg weight. Distinguish internal bus consumption from field-input currents in the S5 power-supply calculation.

If one group fails, check the cabinet fuse and that group’s supply and return. A field short circuit or loose common connection can affect one group of eight.

Input delay and cable length

The ST 50 catalog table gives 2.2–4.6 ms for 0 → 1 and 4.5–12 ms for 1 → 0. The S5-115H manual identifies these as typical/maximum values. The S5-115U manual has a different delay table; for pulse-critical applications, check both the document edition and the installed card.

Maximum signal-cable lengths are 600 m unshielded and 1000 m shielded. Assess voltage drop, shielding and input thresholds alongside these upper limits. Include CPU scan and data-transfer times when evaluating short pulses.

Four-byte addressing through IM 306

In an S5-115U configuration addressed through IM 306, select a 32-channel module with the type switch OFF. The start byte must be divisible by four. For example, start byte 32 = 20h occupies I 32.0–I 35.7; the next available start could be 36 = 24h. Compare the interface addressing panel with the physical installation.

This example does not make the slot number the input-byte address. Match the four input bytes in the PLC program to the IM 306 settings. During troubleshooting, check the first and last channel of each group, then test every channel in sequence.

Similar models and suffix checks

The 430-7LA11 is a separate earlier order number; also check the suffix on a 430-7LA12-Z record. The 420-7LA11 is a different, non-isolated 32-input model. The 434-7LA12 is an eight-input card with a group interrupt function. Similar numbering within the S5 family does not establish direct interchangeability.

Editor’s note

Start with the complete 430-7LA12 marking and any additional suffix. Do not assume it is identical to 430-7LA11; a clear label is a useful first step in selecting a spare.

If eight inputs disappear together, check that group’s M terminal and supply before replacing the card. Bridging the four group commons without reviewing the circuit can remove the isolation the card provides in the installation.

A sensor marked 24 V does not establish the actual voltage at the input. Check quiescent current on two-wire sensors too. Replacing a sound card will not resolve a marginal field signal.

Photograph IM 306 settings before changing them. Check the 32-channel selection and four-byte address block together. If an LED operates while a different program bit is being monitored, review the addressing first.

When buying a used Siemens card, request testing of all 32 channels, observing each of the four groups separately. Include connector contacts and evidence of repair. One responding input does not establish the condition of the whole card.

OtomasyonAVM resources and PDFs

+ S5 digital input modules · About Siemens S5 PLC

+ Siemens S5 shared PDF archive and operating manuals

+ OtomasyonAVM – Siemens S5-115H manual, English PDF. Printed page 17-14 / PDF page 446 covers the exact 430-7LA12.

Related topics

+ 6ES5 430-7LA11 · 6ES5 430-7LA12-Z

+ 6ES5 420-7LA11 · 6ES5 434-7LA12: compare function and isolation arrangements.

Browse SIMATIC S5

+ S5 digital input modules · S5 interface modules · S5 racks

+ SIMATIC S5 · Siemens S5 PLC · Siemens second-hand equipment

Siemens and external references

+ Siemens 6ES5430-7LA12 datasheet – English, 6 February 2020. Exact code, 32 inputs, 24 V DC and S5-115U/F designation.

+ Siemens ST 50, 1998 – English catalog. Printed pages 3/30–3/32 / PDF pages 116–118: grouping, delay, consumption and connectors.

+ Siemens S5-115U Manual – English; EWA 4NEB 811 6130-02b, Edition 04. Printed page 15-21 / PDF page 549: ratings and wiring; section 6.2 / PDF page 155: IM 306 addressing. This edition specifies 0 → 1 delays of 2.6 ms typical / 5.5 ms maximum and 1 → 0 delays of 2.3 ms typical / 5 ms maximum.

+ Siemens S5-115H Manual – English; EWA 4NEB 811 6111-02b, Edition 03. Printed page 17-14 / PDF page 446: delay table used on this page together with ST 50.