6ES5 530-3LA12

Siemens 6ES5 530-3LA12 SIMATIC S5 CP 530 SINEC L1 Communications Processor

The Siemens 6ES5 530-3LA12 is the compact CP 530 communications processor for SINEC L1 in SIMATIC S5 systems. It coordinates data exchange as the master polls the connected PLCs. The Siemens SINEC L1 manual specifies a bus rate of 9,600 bit/s and a maximum of 31 stations including the master.

The CP 530 connects to the BT 777 over a 20 mA TTY current loop. The BT 777 converts that signal to RS-485 on the bus side. The 6ES5 777-0BB00, 6ES5 777-0BC00 and 6ES5 777-1BC00 are distinct bus terminal versions. When tracing a fault, check the S5 connection cable to the CP separately from the cable between stations.

Which rack arrangements use the compact CP 530?

The Siemens CP 530 family manual shows the compact board in the central S5 racks of the S5-135U and S5-150U. The compact board requires an adapter casing in an S5-115U installation. Before selecting a spare, verify the order numbers of the interface hardware, rack and installed CP together.

In the S5-115U power supply table, Siemens shows a dash in the compact-board column for the 3 A PS 951 7LB12. It lists one compact board each for the 7LB21 and 7LD11 in the configurations covered by that manual. Verify the supply current and slot requirements for the 3LA12 hardware revision fitted.

Station roles and related CP models

Siemens shows the existing programmer port used for suitable S5-100U, S5-101U and S5-115U slave stations. The S5-100U CPU 100 is excluded from this slave configuration. On an S5-115U, a separate CP 530 can act as the slave interface when the programmer port needs to remain available.

The CP 530 3LA11 belongs to the same compact family. The 7LA11 and 7LA12 are block-type CP 530 models for the S5-115U. The CP 535 3LB11 and CP 535 3LB12 belong to the SINEC H1 family. For the CP 544 3UA11 and CP 544 3UB11, verify the serial link arrangement in their own documentation.

Editor’s note

Photograph the full order number. Record the 530-3LA12 suffix, rack order number and any adapter casing separately on the service ticket.

Back up the CP configuration. Record the memory submodule, SYSID settings and the master polling list. Include the interrupt list where used.

Read BF and MF separately. BF indicates a bus traffic fault and MF indicates a module fault. Record the LEDs and the CPU operating mode at the same time.

Establish how far the fault extends. If one slave drops out, inspect its address, BT 777 and connection. If several stations disappear together, check the shared bus segment and the master.

Check the station list after fitting a spare. Once the SYSID and polling list are loaded, compare the communicating stations with the machine’s existing station list.

OtomasyonAVM resources and PDFs

About Siemens S5 PLCs · S5 communications modules · Siemens S5 PDF archive. The CP 530 wiring and commissioning manual is in the Siemens external references below.

Related topics

Compact CP 530 3LA11 · S5-115U CP 530 7LA12 · BT 777 1BC00

S5 navigation

Siemens S5 PLCs · S5 communications modules · S5 cables and connectors

Siemens and other external references

Siemens 6ES5530-3LA12 ordering data sheet (Exact order number and compact CP 530 design)

Siemens SIMATIC S5 SINEC L1 / CP 530 manual (Network, BT 777, installation and diagnostics)

Siemens S5 migration guide, section 4.4.2 (Exact 3LA12 order number and SINEC L1 station roles)